(2)
Make sure that the access platform is in position below the opened cargo door.
(3)
Make sure that the access panel(s) is (are) removed from the cargo door.
R 1EFF : 051-052, 1 52-32-21Page 484 1 1 Aug 01/05 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 407/TASK 52-32-21-991-006) Subtask 52-32-21-910-053
A. Preparation ofor the Installation
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Apply a layer of COMMON GREASE (Material No. 04-004) to all moveable parts.
(5)
If removed, install the target (35) on the control lever (34) (Ref. TASK 52-35-13-400-002).
Subtask 52-32-21-420-054
B. Installation of the Locking Shaft
(1)
Connect the shaft levers (25) and (29) to the spring unit (28) of the locking unit as follows:
(a)
Put the fork ends of the shaft levers (25) and (29) on the eye end of each spring unit (28).
(b)
Install the bolt (19), the washers (20), the bush (21) and the nut (22) on the shaft levers (25) and (29).
(c)
Tighten the nut (22) and safety it with the new cotter pin (23).
(2)
Install the locking shaft (18) on the cargo door as follows:
(a)
Move the locking shaft (18) through the lateral cutout of the cargo door into the sliding bearing of each frame fork end.
(b)
During this movement, assemble the shaft levers (25),(29),(36), the interlock cam (30) and the control lever (34) in the correct sequence on the locking shaft (18).
R 1EFF : 051-052, 1 52-32-21Page 485 1 1 Aug 01/05 1 1 1CES 1
(c) Put the shaft levers (25) and (29) , the interlock cam (30) and the control lever (34) in the correct position on the locking shaft (18) (in accordance with your marks).
NOTE : Make sure that the attachment holes are aligned.
____
(d)
Install the tapered pins (24) to attach the shaft levers (25) and (29 and the control lever (34) on the locking shaft (18).
(e)
Install the washers (26) and the nuts (27) on the tapered pins
(24) and tighten the nuts (27).
(3)
Install the tapered pin (33) to attach the interlock cam (30) on the locking shaft (18).
(4)
Install the washer (32) and the nut (31) on the tapered pin (33) and tighten the nut (31).
Subtask 52-32-21-420-055
C. Installation of the Deflection Unit
(1)
Install the shaft end (16) on the locking shaft (18) as follows:
(a)
Move the shaft end (16) into the locking shaft until the attachment holes are aligned.
(b)
Connect both parts with the tapered pins (13), the washer (14) and the nuts (15).
(c)
Move the serrated bush (12) on the shaft end (16) until the attachment holes are aligned.
(d)
Connect both parts with the tapered pins (13), the washer (14) and the nuts (15).
(2)
Install the deflection lever (10) on the shaft end (16) as follows:
(a)
Move the serrated plate (11) with its correct side on the shaft end (16) until it engages with the serrated bush (12).
(b)
Move the deflection lever (10) on the shaft end (16) until it engages with the serrated plate (11).
(c)
Make sure that the positions of the deflection lever (10) and the serrated plate (11) are aligned with your mark.
R 1EFF : 051-052, 1 52-32-21Page 486 1 1 Aug 01/05 1 1 1CES 1
(d) Install the washer (9) and the nut (8) on the threaded end of the shaft end (16).
NOTE : Do not tighten the nut (8) and safety it with the new
____
cotter pin (7) at this time.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(95)
