(e)
 Turn the output shaft of the gear box (27) to make sure that the gear rotates freely.

 (3)
 Connect the shaft lever (10) to the output shaft of the gearbox (27) as follows:

 (a)
 Put the shaft lever (10) in position on the output shaft and make sure that the pin holes are align.

 (b)
 Install the tapered pins (9), the sleeves (16), the washers (17) and the nuts (18) on the shaft lever (10).

 (c)
 Tighten the nuts (18).

 1EFF : 051-052, 1 52-32-21Page 454 1 1 Aug 01/05R 1 1 1CES 1

 (d) Install the protection plug (18) on the top of the shaft lever (10).
 (4) Assemble the drive shaft lever (61) on the drive shaft of the gear box (27) as follows:
 (a)
 Put and hold the safety cam (30) and the lever (35) in the installation position on the cargo door frame.

 (b)
 Put the drive shaft lever (61) through the cargo door frame to engage it with the drive shaft of the gear box (27).

 (c)
 Make sure that the pin holes of the drive shaft lever (61), the lever (35) and the drive shaft are align.

 (d)
 Make sure that the gap between the trust plate (28) and the end of the drive shaft lever (61) is correct.

 NOTE : The gap must be between 0.2 mm (0.0078 in.) and 0.4 mm
____ (0.0157 in.) to make sure that the gear rotates freely.
 (e)
 Install the tapered pins (34), the sleeves (36), the washers (37) and the nuts (38) on the lever (35).

 (f)
 Tighten the nuts (38).

 (g)
 Make sure that the pin holes of the drive shaft lever (61) and the safety cam (30) are aligned.

 (h)
 Install the tapered pins (31), the washers (32) and the nuts (33) on the safety cam (30).

 (i) Tighten the nuts (33). R **ON A/C 106-149, 221-299, 301-399, 401-499,
 Subtask 52-32-21-420-052-A
 C. Installation of the Cover Assembly R **ON A/C 106-149, 221-299, 301-399,
 (Ref. Fig. 405B/TASK 52-32-21-991-004-B)
R 1EFF : 051-052, 106-149, 221-299, 301-399, 1 52-32-21Page 455 1401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 401-499,

R (Ref. Fig. 405D/TASK 52-32-21-991-004-D) R **ON A/C 106-149, 221-299, 301-399, 401-499,
 (1)
 Put the shaft lever (15) in position and install the shaft (16) through the cover assembly (17).

 (2)
 Align the shaft lever (15) with the shaft (16) and install the tapered pin (11),the spacer (7) and the nut (6).

 (3)
 Tighten the nut (6).

 (4)
 Put the cover assembly (17) in position on the beam 4 and install the bolts (19) and the washers (18).

 (5)
 Tighten the bolts (19).

 (6)
 Align the shaft lever (15) with the fork-end of the connection link

 (12) and install the bolt (14), the washers (13) and (8), and the nut (9).

 (7)
 Tighten the nut (9).

 (8)
 Safety the nut (9) with a new cotter pin (10).

 (9)
 Align the shaft lever (3) on the shaft (16) and install the tapered pin (2), the spacer (4), and the nut (5).

 (10) Tighten the nut (5).
 **ON A/C 001-049, 053-099, 101-105, 201-220,

 Subtask 52-32-21-420-066
 D. Installation of the Linkage
 (Ref. Fig. 404/TASK 52-32-21-991-003)

 (1) Connect the connection rod (82) to the vent door lever (85) of the safety shaft as follows:
 (a) Put the lower eye end of the connection rod (82) on the fork end of the vent door lever (85).
R 1EFF : 001-049, 053-099, 101-149, 201-299, 1 52-32-21Page 456 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (b)
 Install the bolt (83), the washers (84) and the nut (86).

 (c)
 Tighten the nut (86) and safety it with the new cotter pin (87).

 (2)
 Connect the connection rod (82) on the lever (80) as follows:

 (a)
 Put the upper eye end of the connection rod (82) on the fork end of the lever (80).

 (b)
 Install the bolt (81), the washers (79) and the nut (78) on the lever (80).

 (c)
 Tighten the nut (78) and safety it with the new cotter pin (77).

 (3)
 Connect the link assy (88) on the drive shaft lever (102) as follows:

 (a)
 Put the fork-end of the link assy (88) on the eye-end of the drive shaft lever (102) and install the bolt (101),the sleeve (100), the washer (98) and the nut (97).

 (b)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(87)