3. Job Set-up
__________
 Subtask 52-32-18-010-051
 A. Get Access
 (1)
 Open the AFT cargo compartment door and safty it with the support struts (Ref. TASK 52-30-00-860-001).

 (2)
 Remove the damaged door seal (Ref. TASK 52-32-18-000-001).

 4. Procedure
_________
 Subtask 52-32-18-330-050
 A. Repair of Minor Cuts and Small Punctures
 (Ref. Fig. 801/TASK 52-32-18-991-004)

 NOTE : A repair of the minor cuts are only permitted if the cuts are not
____ longer than 25.4 mm (1.0 in.). A repair of the small punctures are only permitted if:
 -the punctures are less than 6.4 mm (0.25 in.) and the distance between each punctere is more than 25.4 mm (1.0 in.),
 -there are not more than three punctures within a section of
 200.0 mm (7.87 in.). R In all other cases prepare a splice repair of the door seal R (refer to para: "Repair of Heavily Damaged Areas").
 (1) Drill stop holes of dia. 2.0 mm (0.08 in.) at the ends of the cuts.
 1EFF : ALL 1 52-32-18Page 802 1 1 Aug 01/99 1 1 1CES 1

 Repair of Minor Cuts and small Punctures
 Figure 801/TASK 52-32-18-991-004
 1EFF :  ALL  1  52-32-18 Page 803 
1  1  Feb 01/98
 1  1
 1CES  1

 (2)
 Push the seal to open the cut and very carefully prepare the surfaces

 of the cut or the puncture with a very fine emery cloth.

 (3)
 Prepare the surface of the repair area with a very fine emery cloth .

 (4)
 Carefully degrease the repair area with CLEANING AGENTS (Material No. 11-016) and a lint-free cloth.

 (5)
 Apply a thin coat of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) or BONDING AND ADHESIVE COMPOUNDS (Material No. 08-026) to the opposite surfaces of the cut.

 (6)
 Press the surfaces of the cut puncture together and leave them to dry for some minutes.

 (7)
 Cut a piece of SPECIAL MATERIALS (Material No. 05-024) to the size of the repair area.

 (8)
 Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) or BONDING AND ADHESIVE COMPOUNDS (Material No. 08-026) to the repair area and fill the stop holes.

 (9)
 Put the prepared replacement tissue onto the repair area so that it is as smooth as the seal surface.

 (10)
 Cover the repair area with a layer of foil SPECIAL MATERIALS (Material No. 05-023) and put the seal in the wooden bonding block.

 (11)
 Compress the seal over a period of 24 hours in the wooden bonding block with a clamp.

 (12)
 Remove the wooden bonding block and the foil from the repair area of the seal.

 (13)
 Prepare the repair area with very fine emery cloth to get a smooth surface of the seal.

 Subtask 52-32-18-330-051
 B. Repair of Heavily Damaged Areas (Splice Repair)
 (Ref. Fig. 802/TASK 52-32-18-991-005, 803/TASK 52-32-18-991-006)

 (1) Cut the seal at a minimum distance of 50.0 mm (1.97 in.) from the next inflation hole to remove the damaged section of the seal.
 NOTE : The minimum repair length of the replacement section is:
____
 -for a straight section, 200.0 mm (7.87 in.)
 1EFF : ALL 1 52-32-18Page 804 1 1 Feb 01/98 1 1 1CES 1

 Splice Repair
 Figure 802/TASK 52-32-18-991-005
 1EFF :  ALL  1  52-32-18 Page 805 
1  1  Feb 01/98
 1  1
 1CES  1

 Wooden Bonding Block
 Figure 803/TASK 52-32-18-991-006
 1EFF :  ALL  1  52-32-18 Page 806 
1  1  Feb 01/98
 1  1
 1CES  1

 -for a curved section, 200.0 mm (7.87 in.) measured from the edge of the corner.
 (2) For the straight and the curved section, cut a section of the
 replacement seal to the same length as the removed section.

 NOTE : Make sure that the quantity of the inflation holes are the
____
 same as in the removed section.

 (3)
 Carefully remove the first layer of tissue reinforcement from the ends of the seal and the replacement sections over a length of 25.4 mm (1.0 in.) (repair area).

 (4)
 Prepare the surfaces of the repair areas with emery cloth.

 (5)
 Carefully degrease the surface with CLEANING AGENTS (Material No. 11-016) and a lint-free cloth.

 (6)
 Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(72)