(b)
If removed, install the bushes (17),(27) in the fork ends of the bellcrank lever (16).
(c)
Put the linkage (9) in position on the bellcrank lever (16) and attach it with the bolt (14), the washers (15) and the nut (19).
R 1EFF : 001-049, 051-099, 101-105, 201-220, 1 52-32-21Page A463 1 1 Aug 01/05 1 1 1CES 1
(d)
Put the bellcrank lever (16) (together with the linkage (9)) in position on the journal bearing (13) and attach it with the washer (21) and the nut (22).
(e)
Put the eye end (18) in position on the bellcrank lever (16) and attach it with the bolt (28), the washers (26) and the nut (25).
(f)
Tighten the nuts (19),(22),(25).
(g)
Safety the nut (19) with the new cotter pin (20).
(h)
Safety the nut (22) with the new cotter pin (23).
(i)
Safety the nut (25) with the new cotter pin (24).
(2) Install the drift pin (3) to the edge member as follows:
(a)
If removed, install the bush (4) in the fork end of the drift pin (3).
(b)
Move the drift pin (3) into the edge member bearing.
(c)
Put the linkage (9) on the drift pin (3) and attach it with the bolt (1), the washers (5),(8) and the nut (6).
(d)
Tighten the nut (6) and safety it with the new cotter pin (7) when the drift pin mechanism is correctly adjusted.
Subtask 52-32-21-420-062-C
C. Installation of the Teleflex Controls NOTE : The teleflex control includes the eye ends (18),(37), the upper
____ ball joint (67), the lower ball joint (40) and the ball bearing control (52).
(1) Install the ball bearing control (52) on the cargo door as follows:
(a)
Put the grommet (55) in position on the ball bearing control (52).
(b)
Move the upper end of the control cable (52) through the cutout of the longeron 3 and the frame hole at FR54A.
(c)
Install the lock nuts (50),(51) and the washer (49) on the lower end of the ball bearing control (52).
R 1EFF : 051-052, 1 52-32-21Page A464 1 1 Aug 01/05 1 1 1CES 1
(d)
Move the lower end of the control cable (52) through the frame hole of the longeron 4.
(e)
Adjust the lock nuts (50) and (51) until the distance between the logeron 4 and the recess of the ball bearing control (52) is 95.0 mm (3.7401 in.).
(f)
Install the washer (48) and the lock nuts (46) and (47) on the lower end of the ball bearing control (52).
(g)
Tighten the lock nuts (46) and (47) with your hand. NOTE : Torque and safety these lock nuts when the drift pin
____
mechanism is correctly adjusted.
(h)
Install the lock nuts (56),(57) and the washer (58) on the upper end of the ball bearing control (52).
(i)
Move the upper end of the ball bearing control (52) through the frame hole at FR55.
(j)
Adjust the lock nuts (56) and (57) until the distance between the FR55 and the recess of the ball bearing control (52) is 95.0 mm (3.7401 in.).
(k)
Install the washer (59) and the lock nuts (60),(61) on the upper end of the ball bearing control (52).
(l)
Tighten the lock nuts (60) and (61) with your hand. NOTE : Torque and safety these lock nuts when the drift pin
____
mechanism is correctly adjusted.
(2) If necessary, install the eye ends (18),(37) at the ball joints (67),(40) as follows:
(a)
Install the lock nut (68), the new tab washer (69) and the eye end (18) on the upper ball joint (67).
(b)
Install the lock nut (39), the new tab washer (38) and the eye end (37) on the lower ball joint (40).
(c)
Tighten the lock nuts (68),(39) with your hand. NOTE : Torque and safety the lock nuts (68),(39) when the drift
____
pin mechanism is correctly adjusted.
R 1EFF : 051-052, 1 52-32-21Page A465 1 1 Aug 01/05 1 1 1CES 1 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(115)
