(b)
Attach the shaft lever (25) with the bolt (64), the washer (63) and the nut (62) on the serrated shaft (31).
(4)
Put the mounting bracket (68) to the door structure (67) and attach it with the bolts (65), the washers (66) and the nuts (69),
NOTE : You must install the mounting bracket (68) with force to
____
compress the gas spring (27).
(5)
If removed, install the handle spring (20) as follows:
(a)
Assemble the handle spring (20) with the spring bolt (19).
(b)
Put the spring bolt (19) together with the handle spring (20) in position to the door beam 4.
(c)
Install the mounting nut (18) on the spring bolt (19) to set the handle spring (20) under pre-tension.
(6)
Attach the spring bolt (19) on the roller lever (33) as follows:
(a)
Put the fork-end of the spring bolt (19) to the roller lever (33) so that their bores align.
(b)
Install the bolt (39), the washer (51) and the nut (50) and tighten it.
(7)
Install the control rod (57) on the locking shaft lever (52) as follows:
(a)
Put the lower fork-end of control rod (57) to the locking shaft lever (52) so that their bores align.
(b)
Install the bolt (56), the washers (55) and the nut (54).
(c)
Tighten the nut (54) and safety it with the new cotter pin (53).
R 1EFF : 151-199, 1 52-32-21Page B433 1 1 Aug 01/05 1 1 1CES 1
(8) Install the connection rod (45) on the link lever (40) as follows:
(a) Put the lower fork-end of connection rod (45) in position and install the bolt (44), the washers (43) and the nut (42).
(b) Tighten the nut (42) and safety it with the new cotter pin (41). **ON A/C 001-049, 053-099, 101-149, 201-299, 301-399,
Subtask 52-32-21-420-068
C. Installation of the Door Handle **ON A/C 001-049, 053-099, 101-105, 201-220,
(Ref. Fig. 413/TASK 52-32-21-991-014) **ON A/C 106-149, 221-299, 301-399,
(Ref. Fig. 413A/TASK 52-32-21-991-014-B) **ON A/C 001-049, 053-099, 101-149, 201-299, 301-399,
(1)
Install the door handle (14) on the door structure (17) as follows:
(a)
Put the door handle (14) and the adjustment washers (15) and (16) in position on the door structure (17).
(b)
Move the door handle shaft (26) into the door structure (17) so that it engages with the door handle (14) and the adjustment washers (15) and (16).
(2)
Measure the lateral gaps "A" between the door handle (14) and the door structure.
NOTE : The lateral gaps "A" should have the same size and must be
____ between 1.0 mm (0.0393 in.) and 3.0 mm (0.1181 in.). END
(3) If the lateral gaps "A" are out of tolerance, change the position of the adjustment washers (15) and (16).
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-32-21Page B434 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
(4)
Safety the correct installed door handle shaft (14) as follows:
(a)
Put the lock device (30) into the slot of door handle shaft (14).
(b)
Attach the lock device (30) with the screws (29) on the door structure (17).
(5)
Install the control rod (57) on the shaft lever (25) as follows:
(a)
Put the upper fork-end of the control rod (57) in position and install the bolt (58), the washers (59) and the nut (60).
(b)
Tighten the nut (60) and safety it with the new cotter pin (61).
(6)
Install the connection rod (45) on the Maltese-cross latch (32) as follows:
(a) Put the upper fork-end of the control rod (45) in position and install the bolt (49), the washers (48) and the nut (47).
(b) Tighten the nut (47) and safety it with the new cotter pin (46). R **ON A/C 151-199, 401-499,
Subtask 52-32-21-420-068-A
C. Installation of the Door Handle
(1)
Install the door handle (14) on the door structure (17) as follows:
(a)
Put the door handle (14) and the adjustment washers (15) and (16) in position on the door structure (17).
(b)
Move the door handle shaft (26) into the door structure (17) so that it engages with the door handle (14) and the adjustment washers (15) and (16).
(2)
Measure the lateral gaps "A" between the door handle (14) and the door structure.
NOTE : The lateral gaps "A" should have the same size and must be
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門5(134)
