-
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 (1) Remove the vertical stabilizer fairings 323AL and 323AR (Ref. TASK 53-55-11-000-001).
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
 SPECIAL MATERIAL.
 THIS MATERIAL IS DANGEROUS.

 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (2) Clean the inspection area with CLEANING AGENTS (Material No. 11-003) and a lint-free cloth.
 4. Procedure
_________
 (Ref. Fig. 615/TASK 53-41-00-991-018)
 Subtask 53-41-00-210-074
 A. Detailed Visual Inspection
 (1) Do a detailed visual inspection of the fuselage skin in the circumferential skin splice at:
 -FR70,
 -between STGR10 LH and STGR10 RH,
 -
the crown center line,

 -
the cutout corners for fin attachments,

 EFF : ALL
53-41-00Page 665
May 01/04
R
 CES

 Circumferential Skin Splice FR70 Figure 615/TASK 53-41-00-991-018
R  EFF : CES  ALL  53-41-00 Page 666 May 01/04 

 -the external surface,
 for cracks.

 NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-101) for
____
 the correct repair procedure.

 5. Close-up
________ Subtask 53-41-00-410-092
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the vertical stabilizer fairings 323AL and 323AR (Ref. TASK 53-55-11-400-001).

 (3)
 Remove the warning notice(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 EFF : ALL
53-41-00Page 667
May 01/04
R
 CES  TASK 53-41-00-210-019

 Detailed Visual Inspection of Skin around VHF-3 Antenna Cutout between FR52 and FR53 and between Stringer 1 LH/RH, External Surface
 1.
 Reason for the Job

__________________
 Refer to the MPD TASK: 534112-01

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific  lint-free cloth
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
R  Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
23-12-11-000-002 Removal of the VHF Antenna (4RC3)
 23-12-11-400-002 Installation of the VHF Antenna (4RC3)
 ASRM 53-41-11-101 (for corrective action)
 53-41-00-991-019 Fig. 616

 EFF : ALL
53-41-00Page 668

 3. Job Set-up
__________ Subtask 53-41-00-010-092
 A. Get Access
 (1) Remove the VHF 3 antenna (Ref. TASK 23-12-11-000-002). WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
 SPECIAL MATERIAL.
 THIS MATERIAL IS DANGEROUS.

 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (2) Clean the inspection area with CLEANING AGENTS (Material No. 11-003) and a lint-free cloth.
 4. Procedure
_________
 (Ref. Fig. 616/TASK 53-41-00-991-019) Subtask 53-41-00-210-075
 A. Inspection
 (1) Examine the skin cutout of the VHF 3 antenna for:
 -corrosion,
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(5)