NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-201) for
____
the correct repair procedure.
**ON A/C ALL
5. Close-up
________ Subtask 53-41-00-942-094
A. Remove the ground support equipment.
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
EFF : ALL 53-41-00Page B615
Nov 01/04
R
CES TASK 53-41-00-210-813
General Visual Inspection of Lower Skin of Longitudinal Lap Joints in Crack Stopper Areas at Stringer 32 LH/RH, External Surface
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
1. Reason for the Job
__________________
Refer to the MPD TASK: 534117-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice
No specific 1 ACCESS PLATFORM 1M (3 FT)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL 53-41-00Page B616
Nov 01/04
R
CES C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 53-41-11-101 (for corrective action)
ASRM 53-41-11-201 (for corrective action)
**ON A/C 001-049, 051-099, 101-149, 201-299,
53-41-00-991-066 Fig. 646 R **ON A/C 151-199, 401-499,
53-41-00-991-066-A Fig. 646A
**ON A/C 301-399,
53-41-00-991-066-B Fig. 646B
**ON A/C ALL
3. Job Set-up
__________
Subtask 53-41-00-941-073
A. Install the ground support equipment.
(1) Put a warning notice in position to tell persons not to operate the flight controls.
(2) Put the ACCESS PLATFORM 1M (3 FT) in the required position.
Subtask 53-41-00-110-096
B. Cleaning Procedure WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Clean the area with a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-004), and let the area dry.
4. Procedure
_________
**ON A/C 001-049, 051-099, 101-149, 201-299,
(Ref. Fig. 646/TASK 53-41-00-991-066)
R **ON A/C 151-199, 401-499,
(Ref. Fig. 646A/TASK 53-41-00-991-066-A)
**ON A/C 301-399,
(Ref. Fig. 646B/TASK 53-41-00-991-066-B)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(37)
