(2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 EFF : ALL 53-41-00Page A678

Nov 01/04
R
 CES  TASK 53-41-00-210-808

 General Visual Inspection of Upper Skin of Longitudinal Lap Joints, including Crack Stopper Areas at Stringer 32 LH and Stringer 41 RH, External Surface
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 534104-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  warning notice
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 EFF : ALL  53-41-00Page A679

Nov 01/04
R
 CES

 C. Referenced Information

 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
ASRM 53-41-11-101 (for corrective action)
 ASRM 53-41-11-201 (for corrective action)
 53-41-00-991-051 Fig. 638

 **ON A/C 301-399,
 53-41-00-991-070 Fig. 639
 **ON A/C ALL
 53-41-00-991-081 Fig. 640
 3. Job Set-up
__________
R **ON A/C 001-049, 051-099, 101-149, 201-299,
 Subtask 53-41-00-010-157
 A. Get Access
 (1)
 Put a warning notice in position to tell persons not to operate the flight controls.

 (2)
 Remove these access panels:

 -197AB
 -197BB
 -197GB
 -198BB
 -198GBR **ON A/C 151-199, 401-499,

 Subtask 53-41-00-010-157-A
 A. Get Access
 (1)
 Put a warning notice in position to tell persons not to operate the flight controls.

 (2)
 Remove these access panels:

 -197AB
 -197BB
 -197GB
 -198BB
 -198MB
 **ON A/C 301-399,
 Subtask 53-41-00-010-157-B
 A. Get Access
 (1)
 Put a warning notice in position to tell persons not to operate the flight controls.

 (2)
 Remove these access panels:

 -197AB
 -197GB
 -197KB
 -198GB
 -198KB
 **ON A/C ALL
 Subtask 53-41-00-110-091
 B. Cleaning Procedure
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.

 WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
 (1) Clean the area with a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-004), and let the area dry.
 4. Procedure
_________
 (Ref. Fig. 638/TASK 53-41-00-991-051)
 **ON A/C 301-399,
 (Ref. Fig. 639/TASK 53-41-00-991-070)
 **ON A/C ALL
 (Ref. Fig. 640/TASK 53-41-00-991-081)
R **ON A/C 001-049, 051-099, 101-149, 201-299,
 Subtask 53-41-00-210-110
 A. Inspection
 (1) Examine the following areas for scratches, dents and cracks:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(30)