Nov 01/04
R
CES
3. Job Set-up
__________
Subtask 53-41-00-010-123
A. Get Access
(1)
Put the access platform in position adjacent to the aft
passenger/crew door.
(2)
Open the aft passenger/crew doors (Ref. TASK 52-10-00-010-001), from the outside.
(3)
Remove the scuff-plates (Ref. TASK 53-45-15-000-001), from the aft passenger/crew doors.
Subtask 53-41-00-110-085
B. Cleaning Procedure
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and a lint free cloth, if necessary. Make sure that the area is dry before you continue.
EFF : ALL 53-41-00Page A622
Nov 01/04
R
CES
4. Procedure
_________
Subtask 53-41-00-210-094
A. Detailed Visual Inspection Procedure
(Ref. Fig. 629/TASK 53-41-00-991-038)
(1) Do a detailed visual inspection of the aft passenger/crew door cutout, below the scuff-plates, LH and RH, for corrosion.
NOTE : If required, for information on allowable damage, refer to the
____ ASRM skin plates (Ref. ASRM 53-41-11-101).
5. Close-up
________ Subtask 53-41-00-410-120
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the scuff-plates (Ref. TASK 53-45-15-400-001) at the aft passenger/crew doors.
(3)
Close the aft passenger/crew doors (Ref. TASK 52-10-00-410-001), from the outside.
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
AFT Passenger/Crew Door Cutout, Underneath the Scuff-Plate, LH/RH Figure 629/TASK 53-41-00-991-038
R EFF : ALL 53-41-00Page A624 Nov 01/04
CES **ON A/C 301-399,
TASK 53-41-00-210-042
Detailed Visual Inspection of Skin in Circumferential Splice and Stringer Coupling areas at FR47.5 from Stringer 16 LH/RH to Crown Centerline, External
1. Reason for the Job
__________________
Refer to the MPD TASK: 534149-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth No specific warning notice No specific access platform 5.5 m (18 ft. 1 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 53-00-12-201 (for corrective action) 53-41-00-991-039 Fig. 630
EFF : 301-399, 53-41-00Page A625
Nov 01/04
R
CES 3. Job Set-up
__________ Subtask 53-41-00-010-125
A. Get Access
(1) Put the warning notice in position to tell persons not to operate the flight controls.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(17)
