WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
EFF : ALL
53-55-12Page 407
(4) Apply SPECIAL MATERIALS (Material No. 05-013A) and SEALANTS (Material No. 09-018) to the mating surfaces of the fairings.
Subtask 53-55-12-420-050
B. Installation:
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the fairing (2) in position.
(3)
Install the screws (1) and TORQUE to 0.3 m.daN (26.54 lbf.in).
(4)
Make sure that the clearance 'a' is 1.0 +1.0 -1.0 mm (0.0393 +0.0393-0.0393 in.) between the fairing (2) and the vertical stabilizer fairing (3), and the fairing and the vertical stabilizer (4).
(5)
Make sure that the clearance 'c' is 10.0 +3.5 -3.5 mm (0.3937 +0.1377 -0.1377 in.) between the fairing and the fuselage.
(6)
Apply a bead of SEALANTS (Material No. 09-016) to the edges of the fairing (2).
5. Close-up
________
(Ref. Fig. 401/TASK 53-55-12-991-001) Subtask 53-55-12-410-051
A. Close Access
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
EFF : ALL
53-55-12Page 408
Feb 01/99
R
CES Subtask 53-55-12-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CC1, 5CC2, 14CC1, 14CC2, 15CC, 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 21CE1, 21CE2, 21CE3, 22CE.
EFF : ALL
53-55-12Page 409
FAIRINGS - TRIMMABLE HORIZONTAL STABILIZER - REMOVAL/INSTALLATION
_________________________________________________________________ TASK 53-55-13-000-001 Removal of the Fairings at the THS Fittings.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform 5.3 m (17 ft. 5 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 55-15-11-000-001 Removal of the Apron 333AT/333AB/343AT/343AB 53-55-13-991-001 Fig. 401
3. Job Set-up
__________ Subtask 53-55-13-941-050
A. Aircraft Maintenance Configuration
(1) Put a warning notice in position to tell persons not to operate the flight controls.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
(2) Put the access platform in position at Zones 311 and 312.
EFF : ALL
53-55-13Page 401
Feb 01/99
R
CES EFF : ALL
Subtask 53-55-13-864-050
B. Depressurize the Green, Yellow and Blue hydraulic systems (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002) (Ref. TASK 29-10-00-864-003).
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES_______ ARE CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
Subtask 53-55-13-865-050
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(128)
