R (c) Remove the bolts (40), nuts (41) and washers (42) and remove the
R clamp (52).
R (d) Move the sleeve (54) forward over the shroud (38).
R (e) Disconnect the nut (35) from the union (36) and install the SLIDE
R CONE - APU FUEL (98D28207510000).
R (f) Remove the sleeve (54) and the shroud (38) from the fuel hose
R (37).
R (g) Remove and discard the O-rings (51) from the shrouds (38) and
R (33).
R (h) Put blanking plugs on the disconnected line ends.
R (i) Temporarily attach the hose (37) to the aircraft structure at
R FR77.
R (6) Remove the APU Air-Intake Flap:
R (Ref. Fig. 401/TASK 53-58-11-991-008)
R (a) Disconnect the ball-bearing control cable from the APU intake
R flap diverter (Ref. TASK 49-16-41-000-002).
R (b) Remove the APU air-intake flap (Ref. TASK 49-16-43-000-002).
R (7) Install the Tail Cone Sling:
R (Ref. Fig. 407/TASK 53-58-11-991-013)
R (a) Attach the SLING - R/I TAILCONE to the crane and put the CRANE
R HEIGHT 15 M (50 FT) in position.
R (b) Remove the self-adhesive discs which cover the tail-cone hoisting
R points.
R (c) Remove the hoisting lugs from the hoisting points and install the
R lugs with their eye-ends out of the tail cone structure.
R (d) Attach the hoisting sling to the hoisting lugs.
R (8) Disconnect the Tail Cone:
R (Ref. Fig. 408/TASK 53-58-11-991-014)
R (a) Remove the screws (68) and the access covers (69).
R (b) Remove the nuts (74), the bolts (75) and the washers (76) and
R disconnect the bonding strap (71).
R (c) Make sure that the tail cone is held by the hoist and that the
R weight is not on the attach bolts.
R (d) Remove and discard the cotter pins (73).
R (e) Remove the nuts (72) from the attach bolts (70).
R (f) Install the EXTRACTOR - ATTACH BOLTS, TAIL CONE (98A53407566005)
R and remove the attach bolts (70).
R NOTE : The tool kit with the partnumber 98A53407566005 supersedes____
R the tool kit with the partnumber 98A53407566002. If only
R the tool kit with the partnumber 98A53407566002 is
R available, then it is recommended to continue to use this
R tool kit.
R NOTE : Remove the lower attach bolts before you remove the upper____
R attach bolts.
R (g) Carefully disengage the tail cone from the aircraft.
R (h) Install the tail cone on a stand.
R (i) Remove the hoisting equipment.
**ON A/C ALL
TASK 53-58-11-400-007
Installation of the Fuselage Tail Cone
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft) 98A53407566005 1 EXTRACTOR - ATTACH BOLTS, TAIL CONE 98A53907524000 1 SLING - R/I TAILCONE 98D28207510000 1 SLIDE CONE - APU FUEL
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(143)
