Lower Skin of longitudinal Lap Joints in Crack Stopper Areas at Stringer 32, LH/RH, External Surface Figure 646/TASK 53-41-00-991-066
CES
Lower Skin of longitudinal Lap Joints in Crack Stopper Areas at Stringer 32, LH/RH, External Surface Figure 646A/TASK 53-41-00-991-066-A
CES
Lower Skin of longitudinal Lap Joints in Crack Stopper Areas at Stringer 32, LH/RH, External Surface Figure 646B/TASK 53-41-00-991-066-B
CES NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-101) for
____
the allowable damage limits.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-201) for
____
the correct repair procedure.
R **ON A/C 151-199, 401-499,
Subtask 53-41-00-210-115-A
A. Inspection
(1) Examine the following area for scratches, dents and cracks:
-the lower skin of the longitudinal lap joints in the crack stopper areas at stringer 32, LH/RH between FR 57 and FR 70, external surface.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-101) for
____
the allowable damage limits.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-201) for
____
the correct repair procedure.
**ON A/C 301-399,
Subtask 53-41-00-210-115-B
A. Inspection
(1) Examine the following area for scratches, dents and cracks:
-the lower skin of the longitudinal lap joints in the crack stopper areas at stringer 32, LH/RH between FR 48 and FR 70, external surface.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-101) for
____
the allowable damage limits.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 53-41-11-201) for
____
the correct repair procedure.
**ON A/C ALL
5. Close-up
________ Subtask 53-41-00-942-095
A. Remove the ground support equipment.
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
EFF : ALL 53-41-00Page B623
Nov 01/04
R
CES TASK 53-41-00-210-814
General Visual Inspection of Fuselage Skin around AFT Passenger/Crew Door Cutouts, External Surface (except Area under Scuff Plates), LH/RH
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
1. Reason for the Job
__________________
Refer to the MPD TASK: 534131-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific 1 ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
EFF : ALL 53-41-00Page B624
Nov 01/04
R
CES
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 53-41-11-101 (for corrective action) ASRM 53-41-11-201 (for corrective action) 53-41-00-991-069 Fig. 647
3. Job Set-up
__________
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身3(38)
