A. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-16Page 307 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 TASK 32-43-16-600-001- 01
Reactivation of the Alternate-Brake Safety-Valve
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-43-00-710-001 Operational Check of Alternate Braking System 32-43-00-870-002 Bleeding of the High Pressure Alternate Braking
System
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-16Page 308 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
3. Job Set-up
__________ Subtask 32-43-16-941-055
A. Safety Precautions
(1)
Put the access platform in position at the applicable zone 571(671).
(2)
Put the safety barriers in position.
(3)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(4)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
4. Procedure
_________ Subtask 32-43-16-440-054
A. Reactivation of the Alternate-Brake Safety-Valve
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
WARNING : DO NOT LET OIL STAY ON YOUR SKIN FOR A LONG TIME AS IT CAN
_______
CAUSE INJURY.
CAUTION : MAKE SURE THAT THE FLUID DOES NOT STAY ON THE AIRCRAFT
_______ STRUCTURE. IF THE FLUID GETS ON THE AIRCRAFT STRUCTURE, WASH IT OFF IMMEDIATELY WITH SOAP AND WATER.
(1)
Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-002).
(2)
Depressurize the reservoir of the Yellow hydraulic system (Ref. TASK 29-14-00-614-001).
(3)
Bleed the alternate brake system (Ref. TASK 32-43-00-870-002).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-16Page 309 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 Subtask 32-43-16-710-053
B. Test
(1) Do an operational test of the Alternate Braking System (Ref. TASK 32-43-00-710-001).
5. Close-up
________ Subtask 32-43-16-942-053
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-16Page 310 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 SAFETY VALVE - ALTERNATE BRAKE (2620GM,2621GM,2622GM,2623GM)
____________________________________________________________ REMOVAL/INSTALLATION
____________________
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(85)
