Subtask 32-42-16-941-051
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
1EFF : ALL 1 32-42-16Page 413 1 1 Aug 01/05 1 1 1CES 1
(3)
On the panel 400VU:
-
make sure that the landing-gear control-lever 6GA is in the DOWN position
-
make sure that the warning notice is in position in the cockpit to tell persons not to operate the landing gear.
(4)
Make sure that warning notices are in position to tell persons not to pressurize the Green hydraulic system.
Subtask 32-42-16-860-052
B. Aircraft Maintenance Configuration
(1)
Make sure the the Green hydraulic system is depressurized (Ref. TASK 29-10-00-864-001).
(2)
Make sure that the Green hydraulic reservoir is depressurized (Ref. TASK 29-14-00-614-001).
(3)
Make sure that the access platform is in position below the applicable normal-brake servovalve manifold assembly.
(4)
Make sure the Isolation Coupling of the Power Transfer Unit (PTU) is disconnected (Ref. TASK 29-23-00-860-001).
Subtask 32-42-16-865-051
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33 121VU HYDRAULIC/G HYD/PUMP ENG1/MONG 1702GK R34
1EFF : ALL 1 32-42-16Page 414 1 1 Nov 01/04R 1 1 1CES 1
4. Procedure
_________ R **ON A/C 001-003, 051-052,
Subtask 32-42-16-420-050
A. Preparation for Installation
(1)
Use a clean MISCELLANEOUS (Material No. 19-003) and CLEANING AGENTS (Material No. 11-026) to clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
If you install a new manifold (22), remove the blanking plugs and install these items:
-
the pressure transducers (20) and (21) (Ref. TASK 32-42-21-400-001)
-
the safety valves (6) (Ref. TASK 32-42-36-400-001)
-
the servovalves (10) and (15) (Ref. TASK 32-42-48-400-001).
Subtask 32-42-16-420-051
B. Installation of the Normal-Brake Servovalve Manifold Assembly
(1)
Remove the blanking plugs from the hydraulic line end-fittings and the blanking caps from the electrical connectors.
(2)
Make sure that the hydraulic line end-fittings are serviceable.
(3)
Apply SEALANTS (Material No. 09-018) to the interfaces of the normal-brake servovalve manifold assembly and the mounting brackets.
NOTE : You must install the normal-brake servovalve manifold assembly
____ on to the mounting rail while the sealant is wet.
(4)
Hold the normal-brake servovalve manifold assembly in position on the mounting rail.
(5)
Install the parts that follow:
-
the brackets (11) and (19)
-
the bonding strap (18) (Ref. TASK 20-28-00-912-004)
-
the bolts (13)
-
the washers (12)
1EFF : ALL 1 32-42-16Page 415 1 1 May 01/05 1 1 1CES 1
-
the washers (3)
-
the nuts (4).
(6)
Safety the nuts (4) with the new cotter pins (5).
(7)
Install the electrical harnesses on the brackets (11) and (19) (Ref. TASK 32-11-43-400-002).
(8)
Connect the hydraulic unions (1), (2), (7) and (8).
(9)
TORQUE the hydraulic unions (1), (7) and (8) to between 2.4 and 2.8 m.daN (17.69 and 20.64 lbf.ft).
(10)
TORQUE the hydraulic union (2) to between 4.79 and 5.23 m.daN (35.32 and 38.56 lbf.ft).
(11)
Install the electrical connectors: CAUTION : MAKE SURE THAT THE SERVO-VALVE AND PRESSURE-TRANSDUCER
_______ ELECTRICAL CONNECTORS ARE CORRECTLY CONNECTED TO THEIR RELATED EQUIPMENT. IF THE ELECTRICAL CONNECTORS ARE INCORRECTLY CONNECTED, DAMAGE TO THE BRAKE ANTI-SKID SYSTEM WILL OCCUR.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(6)
