R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-14Page 608 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 Subtask 32-43-14-860-055
B. Aircraft Maintenance Configuration
(1)
Open the Main Landing Gear (MLG) doors (Ref. TASK 32-12-00-010-001)
(2)
Put the access platform in position.
(3)
Depressurize the Yellow Hydraulic System (Ref. TASK 29-10-00-864-002)
Subtask 32-43-14-010-053
C. Remove the belly fairing panel 148FB, (Ref. TASK 53-35-13-000-001).
Subtask 32-43-14-941-054
D. Safety Precautions
(1)
Put the warning notices in position to tell persons not to pressurize the yellow hydraulic system: - on the panel 40VU in the cockpit, - on the ground service panel of the yellow hydraulic system.
(2)
Put the safety barriers in position.
Subtask 32-43-14-865-057
E. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33 121VU HYDRAULIC/HYD POWER/Y 3803GX N30 121VU HYDRAULIC/Y HYD/PUMP ENG2/MONG 3700GD Q37 121VU HYDRAULIC/Y HYD/PUMP ENG2/CTL 3701GD Q36 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-14Page 609 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
4. Procedure
_________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Post SB 32-1199 For A/C 001-049,051-058,101-101, R
Subtask 32-43-14-210-054
A. Preparation for Inspection
(Ref. Fig. 602/TASK 32-43-14-991-002)
(1)
Cut and discard the safety wire (5).
(2)
Remove the screws (4) and the washers (3).
(3)
Carefully remove the cover (2) from the BDDV 2577GM (1).
(4)
Do the Inspection for Corrosion
(a)
Use a strong flashlight and inspection mirror and examine the BDDV 2577GM (1).
(b)
If no corrosion is found, do step 4. A. (5) (a).
(c)
No corrosion is permitted on:
-
the bearings and turning parts of the rocker arms (6),
-
the needles and seats,
-
the spherical head rod assemblies. If corrosion is found in these areas, replace the BDDV 2577GM (Ref. TASK 32-43-14-000-001) and (Ref. TASK 32-43-14-400-001).
(d)
If light corrosion is found on:
-
the support (9),
-
the rocker arm (6),
-
the hexagonal heads of the screws (7),
-
the hexagonal heads of the assembly (8). Lubricate these parts as follows.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-14Page 610 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 (5) Lubrication
(a) Use a thin brush and apply COMMON GREASE (Material No. 04-011) around:
-
the 2 rocker arms (6).
-
the spherical head rod assemblies (8),
-
the support (9),
-
the needles,
-
the turning parts of the rocker arms. Carefully remove too much grease.
Subtask 32-43-14-410-054
B. Close Up
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Put the cover (2) in position on the BDDV 2577GM (1).
(3)
Install the washers (3) and the screws (4).
(4)
Tighten the screws (4) and TORQUE them to between 0.3 and 0.4 m.daN
(26.54 and 35.39 lbf.in).
(5)
Safety the screws (4) with MISCELLANEOUS (Material No. 19-009).
Subtask 32-43-14-865-058
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(82)
