(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
1EFF : ALL 1 32-42-48Page 407 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-42-48Page 408 1 1 Nov 01/98 1 1 1CES 1 1EFF : ALL 1 32-42-48Page 409 1 1 Feb 01/03 1 1 1CES 1 1EFF : ALL 1 32-42-48Page 410 1 1 Feb 01/03 1 1 1CES 1
R R R R (3) On the panel 400VU: - make sure that the landing-gear control-lever 6GA is in the DOWN position - make sure that the warning notice is in position to tell persons not to operate the landing gear.
(4) Make sure that the warning notice is in position to tell persons not to pressurize the Green and Yellow hydraulic systems.
Subtask 32-42-48-860-054
B. Aircraft Maintenance Configuration
(1) Make sure that the access platform is in position below the applicable servovalve, at zone 730 or 740.
(2) Make sure the isolation coupling of the PTU is disconnected (Ref. TASK 29-23-00-860-001).
(3) Make sure that the Yellow and Green hydraulic systems are de-pressurized (Ref. TASK 29-00-00-864-001) and (Ref. TASK 29-10-00-864-002).
(4) Make sure that the applicable hydraulic reservoirs have been depressurized (Ref. TASK 29-14-00-614-001).
Subtask 32-42-48-865-051
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 121VU HYDRAULIC/G HYD/PUMP ENG1/MONG 4GG 3GG 1GG 2GG 1702GK M36M35M34M33R34
4. Procedure_________
(Ref. Fig. 401/TASK 32-42-48-991-001)
Subtask 32-42-48-420-053
R A. Preparation for Installation
R R (1) Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
(3) Do an inspection of the component interface and/or the adjacent area.
(4) Examine the interface of the servovalve and the normal brake manifold for the correct condition.
(5) Remove the blanking cap from the electrical connector (4).
(6) If you are to install the servovalve 15GG(16GG), remove the blanking cap from the electrical connector (4) of the servovalve 17GG(18GG).
(7) Remove the blanking plugs from the hydraulic line end-fittings.
(8) Make sure that the hydraulic line end-fittings are serviceable.
(9) Lubricate the new seals (3) and the new rings (2) with HYDRAULIC FLUIDS (Material No. 02-003).
Subtask 32-42-48-420-051
R B. Installation of the Normal Brake Servovalve
(1) Install the seals (3) and the rings (2) on the servovalve (1).
(2) Remove the cover and the blanking plugs from the normal brake manifold.
(3) Put the servovalve (1) in position on the normal brake manifold and install the bolts (5).
R (4) TORQUE the bolts (5) to between 0.35 and 0.45 m.daN (30.97 and 39.82 lbf.in).
R Subtask 32-42-48-760-050
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(35)
