(1)
 Install the new packings (9), the new washer-packings (8) and the elbows union (6) with the nuts (7) on the master cylinder (13) (Ref. TASK 20-23-11-911-002).

 (2)
 Put the master cylinder (13) in position.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-12Page 408 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 (3)
 Install the screw (1) and the washer (2).

 (4)
 Install the washer (3) and the nut (4). Tighten the nut (4).

 (5)
 Install the new cotter pin (5).

 (6)
 Install the bolt (11) and the washer (12).

 (7)
 Install the washer (14) and the nut (15). Tighten the nut (15).

 (8)
 Install the new cotter pin (16).

 (9)
 Adjust the direction of the elbow unions (6) to connect the hoses

 (10) and (17).
 (10)
 TORQUE the nuts (7) to between 0.83 and 0.94 m.daN (73.45 and 83.18 lbf.in) to safety the elbow unions (6).

 (11)
 Remove the blanking plug from the hose (17).

 (12)
 Connect the hose (17) to the master cylinder (13).

 (13)
 TORQUE the hose (17) to between 1.52 and 1.63 m.daN (11.20 and 12.02 lbf.ft).

 (14)
 Remove the blanking plug from the hose (10).

 (15)
 Connect the hose (10) to the master cylinder (13).

 (16)
 TORQUE the hose (10) to between 1.52 and 1.63 m.daN (11.20 and 12.02 lbf.ft).

 Subtask 32-43-12-612-050
 B. Fill the control system of the Alternate braking (Ref. TASK 32-43-00-612-001).
 Subtask 32-43-12-710-050
 C. Operational test
 (1) Do the operational test of the Alternate braking system (Ref. TASK 32-43-00-710-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-12Page 409 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 5. Close-up
________ Subtask 32-43-12-410-050
 A. Close the access
 (1)
 Remove the container.

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Close the access door 811.

 (4)
 Remove the access platform(s).

 (5)
 Remove the warning notices.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-12Page 410 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 DUAL VALVE - ALTERNATE BRAKE DISTRIBUTION (2577GM) - REMOVAL/INSTALLATION

_________________________________________________________________________
 TASK 32-43-14-000-001
 Removal of the Dual-Valve 2577GM Alternate Brake-Distribution
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------

No specific blanking plugs
 No specific bleed hose
 No specific circuit breaker(s) safety clip(s)
 No specific warning notices
 No specific FILLER ADAPTOR TMH DI43-32-00
 No specific access platform 2.0 m (6 ft. 7 in.)
 No specific access platform 2 m (6 ft. 7 in.)
 No specific container 5 l (1.3208 USgal)

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-43-14Page 401 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
29-00-00-910-002 Safety Procedures of the Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-23-00-860-001 Disconnection of the Isolation Coupling of the Power
 Transfer Unit (PTU) 32-12-00-010-001 Open the Main Gear Doors for Access 32-44-11-200-001 Check Nitrogen Charge Pressure On Parking/Emergency
 Accumulator By Reading Gauge
 32-43-14-991-004 Fig. 401
R
R 32-43-14-991-005-A Fig. 402
R
 3. Job Set-up
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(75)