(2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (4)
 Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).

 (5)
 Apply HYDRAULIC FLUIDS (Material No. 02-003), HYDRAULIC FLUIDS (Material No. 02-003A), HYDRAULIC FLUIDS (Material No. 02-003B), HYDRAULIC FLUIDS (Material No. 02-003C) or HYDRAULIC FLUIDS (Material No. 02-003D) to the threads of the throttle valve (1).

 1EFF : ALL 1 32-42-76Page 408 1 1 Aug 01/05 1 1 1CES 1

 (6) Apply HYDRAULIC FLUIDS (Material No. 02-00), HYDRAULIC FLUIDS (Material No. 02-003A), HYDRAULIC FLUIDS (Material No. 02-003B), HYDRAULIC FLUIDS (Material No. 02-003C) or HYDRAULIC FLUIDS (Material No. 02-003D) to the new packing (3).
R **ON A/C ALL
 4. Procedure
_________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 (Ref. Fig. 401/TASK 32-42-76-991-001)
 Subtask 32-42-76-420-051
 A. Installation of the Trottle Valve (1)
 (1)
 Remove the blanking plugs.

 (2)
 Put the packing (3) on the throttle valve (1).

 (3)
 Install the throttle valve (1) in the elbow (4).

 CAUTION : BE CAREFUL WHEN YOU INSTALL THE THROTTLE VALVE. A RED
_______ ARROW, IDENTIFIED AS 'F' IS SHOWN ON SOME THROTTLE VALVES. THE ARROW SHOWS THE DIRECTION OF THE THROTTLE AND NOT THE DIRECTION OF THE FLOW. THUS, WHEN YOU INSTALL THE THROTTLE VALVE, MAKE SURE THAT THE ARROW POINTS AWAY FROM THE AUTOMATIC SELECTOR. IF YOU INSTALL THE THROTTLE VALVE IN THE INCORRECT DIRECTION, YOU CAN CAUSE DAMAGE TO THE SYSTEM.
 (4)
 TORQUE the throttle valve (1) to between 3.19 and 3.47 m.daN (23.52 and 25.58 lbf.ft).

 (5)
 Put the elbow (4) with the throttle valve (1) in position and connect the connectors (2) and (5) to the throttle valve (1) and the automatic selector (6).

 (6)
 TORQUE the connectors (2) and (5) to between 5.4 and 5.9 m.daN (39.82 and 43.51 lbf.ft).

 (7)
 Mark the connections with PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-010).

 1EFF : ALL 1 32-42-76Page 409 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-42-76-865-054

 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1701GK, 1702GK, 1GG, 2GG, 3GG, 4GG.
 Subtask 32-42-76-860-052
 C. Preparation for Test
 (1) Connect the PTU isolation coupling (Ref. TASK 29-23-00-860-002). Subtask 32-42-76-710-050
 D. Test
 (1)
 Do the operational test of the normal braking system (Ref. TASK 32-42-00-710-001).

 (2)
 Make sure that there is no hydraulic fluid leakage from the throttle valve 2581GM.

R **ON A/C ALL
 5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 Subtask 32-42-76-410-050
 A. Close Access
 (1)
 Apply corrosion protection to the connectors (2) and (5) and the adjacent areas (Ref. TASK 51-75-13-916-002).

 (2)
 Remove the container.

 (3)
 Remove the warning notice(s).

 (4)
 Remove the access platform(s).

 (5)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (6)
 Close the right MLG door (Ref. TASK 32-12-00-410-001).

 1EFF : ALL 1 32-42-76Page 410 1 1 Aug 01/05 1 1 1CES 1

 (7) Remove the ground support and maintenance equipment, the special and

 standard tools and all other items.

 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-42-76Page 411 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 CHECK VALVE - NORMAL BRAKE RETURN (2593GM,2594GM) - REMOVAL/INSTALLATION

________________________________________________________________________
 TASK 32-42-77-000-001
 Removal of the Normal Brake-Return Check-Valve
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1. Reason for the Job
__________________
 Self Explanatory
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(47)