Subtask 32-44-17-865-050
 D. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/Y BRK/PRESS/IND 61GG C10 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33 121VU HYDRAULIC/PARK BRK/CTL/STBY 71GG N37 121VU HYDRAULIC/PARK BRK/CTL/NORM 70GG N36 121VU HYDRAULIC/HYD POWER/Y 3803GX N30 121VU HYDRAULIC/Y HYD/PUMP ENG2/MONG 3700GD Q37 121VU HYDRAULIC/Y HYD/PUMP ENG2/CTL 3701GD Q36 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
 Subtask 32-44-17-941-050
 E. Safety Precautions
 (1) Put the warning notices in position to tell persons not to pressurize the Yellow hydraulic system: - on the panel 40VU in the cockpit, - on the ground service panel of the Yellow hydraulic system.
 Subtask 32-44-17-560-051
 F. Component Removal
 (1)
 Remove the pressure relief valve 3067GM (Ref. TASK 32-44-15-000-001).

 (2)
 Remove the hydraulic pressure transducer 3068GN (Ref. TASK 29-32-11-000-004).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-44-17Page 403 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 4. Procedure
_________
 (Ref. Fig. 401/TASK 32-44-17-991-001) Subtask 32-44-17-020-051
 A. Removal of the Brake Manifold 3016GM
 (1)
 Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002).

 (2)
 Remove the nuts (12) and the washers (14).

 (3)
 Remove the bolts (19) the washers (18) and the top half of the clamp (17).

 (4)
 Disconnect the pipe (1) from the manifold (2).

 (5)
 Disconnect the T-assembly (5) from the check valve (6).

 (6)
 Disconnect the pipes (3), (4) and (8).

 (7)
 Disconnect the elbow assembly (9) from the manifold (2).

 (8)
 Put blanking plugs on the disconnected line ends.

 (9)
 Remove the bolts (10), the washers (11) and remove the manifold (2) from the aircraft structure.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-44-17Page 404 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 Alternate Brake Manifold 3016GM
 Figure 401/TASK 32-44-17-991-001

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-44-17Page 405 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 TASK 32-44-17-400-001

 Installation of the Brake Manifold 3016GM
 WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK AREA WHEN
_______ YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES AND A MASK.
 WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______ YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
 1. Reason for the Job
__________________
 Self Explanatory
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-44-17Page 406 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notices
 No specific Torque Wrench : range 0.20 to 3.60 m.daN

 (2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
 (8.00 to 75.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(138)