(b)
 Identify and connect each electrical connector (18) and (19) to its related pressure-transducer (21) and (22).

R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 32-42-16-420-050-A
 A. Preparation for Installation
 (1)
 Use a clean MISCELLANEOUS (Material No. 19-003) and CLEANING AGENTS (Material No. 11-026) to clean the component interface and/or the adjacent area.

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 1EFF : ALL 1 32-42-16Page 416 1 1 Aug 01/05 1 1 1CES 1

 (4) If you install a new manifold (19), remove the blanking plugs and install these items:
 -
the pressure transducers (17) and (18) (Ref. TASK 32-42-21-400-001)

 -
the safety valves (3) (Ref. TASK 32-42-36-400-001)

 -
the servovalves (7) and (12) (Ref. TASK 32-42-48-400-001).

 Subtask 32-42-16-420-051-A
 B. Installation of the Normal-Brake Servovalve Manifold Assembly
 (1)
 Remove the blanking plugs from the hydraulic line end-fittings and the blanking caps from the electrical connectors.

 (2)
 Make sure that the hydraulic line end-fittings are serviceable.

 (3)
 Apply SEALANTS (Material No. 09-018) to the interfaces of the normal-brake servovalve manifold assembly and the mounting lugs of the MLG leg assembly.

 NOTE : You must install the normal-brake servovalve manifold assembly
____ on to the MLG mounting lugs while the sealant is wet.
 (4)
 Hold the normal-brake servovalve manifold assembly in position on the MLG leg mounting lugs.

 (5)
 Install the parts that follow:

 -
the brackets (8) and (16)

 -
the bonding strap (15) (Ref. TASK 20-28-00-912-004)

 -
the new tab washers (9)

 -
the bolts (10).

 (6)
 TORQUE the bolts (10) to between 1.6 and 1.8 m.daN (11.79 and 13.27 lbf.ft).

 (7)
 Bend the ends of the tab washers (9) to lock the bolts (10).

 (8)
 Install the electrical harnesses on the brackets (8) and (16) (Ref. TASK 32-11-43-400-002).

 (9)
 Connect the hydraulic unions (1), (2), (4) and (5).

 (10)
 TORQUE the hydraulic unions (1), (4) and (5) to between 2.4 and 2.8 m.daN (17.69 and 20.64 lbf.ft).

 (11)
 TORQUE the hydraulic union (2) to between 4.79 and 5.23 m.daN (35.32 and 38.56 lbf.ft).

R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-42-16Page 417 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (12) Install the electrical connectors: CAUTION : MAKE SURE THAT THE SERVO-VALVE AND PRESSURE-TRANSDUCER
_______ ELECTRICAL CONNECTORS ARE CORRECTLY CONNECTED TO THEIR RELATED EQUIPMENT. IF THE ELECTRICAL CONNECTORS ARE INCORRECTLY CONNECTED, DAMAGE TO THE BRAKE ANTI-SKID SYSTEM WILL OCCUR.
 (a)
 Identify and connect each electrical connector (6) and (11) to its related servo-valve (7) and (12).

 (b)
 Identify and connect each electrical connector (13) and (14) to its related pressure-transducer (17) and (18).

 **ON A/C ALL
 Subtask 32-42-16-865-052
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GG, 2GG, 3GG, 4GG, 1702GK.
 Subtask 32-42-16-870-050
 D. Preparation for Test
 (1)
 Connect the Isolation Coupling of the PTU (Ref. TASK 29-23-00-860-002).

 (2)
 Bleed the normal brake system (Ref. TASK 32-42-00-870-001).

 (3)
 Make sure that the work area is clean and clear of tool(s) and other items.

 Subtask 32-42-16-710-050
 E. Test
 (1)
 Do an operational test of the normal brake system (Ref. TASK 32-42-00-710-001).

 (2)
 Do an operational test of the anti-skid inhibition (Ref. TASK 32-42-00-710-003).

 (3)
 Make sure that there are no leaks from the normal-brake servovalve manifold assembly and the hydraulic unions.

 1EFF : ALL 1 32-42-16Page 418 1 1 May 01/05R 1 1 1CES 1

 5. Close-up
________ Subtask 32-42-16-942-051
 A. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架7(7)