曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  COMPOUNDS (Material No. 08-060) (4) 
R  - the tape length must extend to the primary or secondary 
R  structure (5) at both ends of the edge with the missing 
R  fastener (3). 
R  (c) If a cover strip (6) is installed between the panel with the 
R  missing fastener (3) and the adjacent panel: 
R  - make an overlap from the panel with the missing fastener (3) to 
R  the adjacent panel through the cover strip (6) 
R  - do this with the Highspeed Tape (4) or the BONDING AND ADHESIVE 
R  COMPOUNDS (Material No. 08-060) (4) 
R  - the tape (4) must extend to the next fasteners adjacent to the 
R  sealed hole (3).
 NOTE : Up to 100 Flight Hours (10 days), a visual inspection of____
 the repair area is necessary once a week. From 100 Flight
 Hours to 500 Flight Hours (50 days), you must do a visual
 inspection of the repair area every day. A new fastener
 assembly must be installed within 500 flight hours after 
R  the installation of the Highspeed Tape (4) or the BONDING 
R  AND ADHESIVE COMPOUNDS (Material No. 08-060) (4).
 5. Close-up________ 
R  **ON A/C 001-049, 101-105,
 Subtask 25-54-12-865-066
 A. Remove the safety clip(s) and the tag(s) and close this(these) circuit
 breaker(s):
 2MY
 3MY.

 EFF : ALL
25-54-12Page 808
May 01/05

 Subtask 25-54-12-410-055-A
 B. Close Access
 (1)
 Remove the access platform(s).

 (2)
 Remove the actuator safety lock and close the FWD cargo-compartment door (Ref. TASK 52-30-00-860-002).

 (3)
 Remove the warning notice(s).

 (4)
 Make sure that the work area is clean and clear of tool(s) and other items.

R **ON A/C 051-099, 106-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 25-54-12-410-055
 B. Close Access
 (1)
 Remove the access platform(s).

 (2)
 Remove the actuator safety lock and close the FWD cargo-compartment door (Ref. TASK 52-30-00-860-002).

 (3)
 Make sure that the work area is clean and clear of tool(s) and other items.

 EFF : ALL
25-54-12Page 809

 STANCHION - DOOR NET - REMOVAL/INSTALLATION
___________________________________________
 TASK 25-54-17-000-001 Removal of the Net Stanchions in the FWD Cargo Compartment
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  1 ACCESS PLATFORM 2M (6 FT)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001  Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 25-54-17-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 25-54-17-010-050
 A. Get Access
 (1)
 Open the FWD cargo-compartment door and install the actuator safety lock (Ref. TASK 52-30-00-860-001).

 (2)
 Put the ACCESS PLATFORM 2M (6 FT) in position at the opening of the FWD cargo-compartment door.

 EFF : ALL
25-54-17Page 401

 4. Procedure
_________ Subtask 25-54-17-020-050
 A. Removal of the Net Stanchions
 (Ref. Fig. 401/TASK 25-54-17-991-001)

 (1)
 Disconnect the net fittings from the applicable net attachment fittings of the cargo-compartment floor and ceiling areas.

 (2)
 Remove the stanchions (2). NOTE : The removal procedure for all the stanchions (2) is the same.

____ Thus, the removal procedure for one stanchion (2) only is given here.
 (a)
 Turn the locking base (3) counterclockwise to unlock the stanchion from the tiedown point (4).

 (b)
 Push the stanchion (2) up to release the stanchion locking base

 (3) from the tiedown point (4).

 (c)
 Move the lower part of the stanchion (2) away from the tiedown point (4). Then move the stanchion (2) down to remove the stanchion plunger from the upper ceiling fitting (1).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(9)