25-54-41-991-001-B  Fig. 401B
 EFF : ALL
25-54-41Page 401

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-149, 201-299,
 25-54-41-991-002 Fig. 402 R **ON A/C 151-199, 401-499,
 25-54-41-991-002-A Fig. 402A
 **ON A/C 301-399,

 25-54-41-991-002-B Fig. 402B
 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 25-54-41-010-050

 A. Get Access
 (1)
 Open the FWD cargo-compartment door and install the actuator safety lock (Ref. TASK 52-30-00-860-001).

 (2)
 Put the access platform in position at the opening of the FWD cargo-compartment door.

 **ON A/C 062-099, 106-149, 203-299,
 Subtask 25-54-41-865-050
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL SERVICE IDENT. LOCATION -------------------------------------------------------------------------------2000VU SEMI AUTO CLS-FWD 2MY B3 2000VU SEMI AUTO CLS-FWD 3MY B1
 EFF : ALL
25-54-41Page 402

 **ON A/C ALL
 4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 201-299,
 Subtask 25-54-41-020-050
 A. Removal of the Tie-Down and Net Attachment Fittings from the Floor Area (Ref. Fig. 401/TASK 25-54-41-991-001)
 (1)
 Remove the cargo net(s) (6), if installed:

 (a)
 Disconnect the net fittings (7) from the applicable net attachment fittings of the cargo-compartment floor and ceiling areas.

 (b)
 Remove the cargo net(s) (6).

 (2)
 Remove the tie-down points (2): NOTE : The removal procedure for all the tie-down points (2) is the

____ same. Therefore, the removal procedure for one tie-down point
 (2) only is given here.
 (a)
 Remove the screws (1) from the tie-down point (2).

 (b)
 Remove the tie-down point (2) from the structure (3).

 (3)
 Remove the seat-track section (5):

 (a)
 Remove the screws (4) from the seat-track section (5).

 (b)
 Remove the seat-track section (5) from the structure (3).

 (4)
 Remove the tie-down points (9): NOTE : The removal procedure for all the tie-down points (9) is the

____ same. Therefore, the removal procedure for one tie-down point
 (9) only is given here.
 (a)
 Remove the screws (8) from the tie-down point (9).

 (b)
 Remove the tie-down point (9) from the plug housing (10).

 EFF : ALL
25-54-41Page 403

 Tie-Down and Net Attachment Fittings - FWD Cargo-Compartment Floor Area Figure 401/TASK 25-54-41-991-001
R EFF : 001-049, 051-099, 101-149, 201-299, 25-54-41Page 404 May 01/05
 CES

 (c) If necessary, remove the plug housing (10) from the structure (3).
 (5) Remove the tie-down fittings (12): NOTE : The removal procedure for all the tie-down fittings (12) is
____ the same. Therefore, the removal procedure for one tie-down fitting (12) only is given here.
 (a)
 Remove the screws (11) from the tie-down fitting (12).

 (b)
 Remove the tie-down fitting (12) from the structure (3).

 (6)
 Remove the tie-down fitting (14):

 (a)
 Remove the screws (13) from the tie-down fitting (14).

 (b)
 Remove the tie-down fitting (14) from the structure (3).

 (7)
 Remove the tie-down fittings (16): NOTE : The removal procedure for all the tie-down fittings (16) is

____ the same. Therefore, the removal procedure for one tie-down fitting (16) only is given here.
 (a) Remove the screws (15) from the tie-down fitting (16).
 (b) Remove the tie-down fitting (16) from the structure (3). R **ON A/C 151-199, 401-499,
 Subtask 25-54-41-020-050-A
 A. Removal of the Tie-Down and Net Attachment Fittings from the Floor Area (Ref. Fig. 401A/TASK 25-54-41-991-001-A)
 (1) Remove the cargo net(s) (1), if installed:
 (a)
 Disconnect the net fittings (2) from the applicable net attachment fittings of the cargo-compartment floor and ceiling areas.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(11)