_
 pack-assembly (9), to disengage the spring clips. 2 Disengage the spring loaded bolts (73) and remove the
_ decorative-cover (20).
 (c) Keep the decorative-cover (20) with the aircraft.

 (2) Safety the inflation reservoir of the escape-slide: WARNING : MAKE SURE THAT THE SAFETY/LOCK PIN IS CORRECTLY INSTALLED
_______ IN THE REGULATOR VALVE ASSEMBLY OF THE INFLATION RESERVOIR. THIS PREVENTS ACCIDENTAL:
 -DISCHARGE OF THE INFLATION RESERVOIR
 -DEPLOYMENT OF THE ESCAPE-SLIDE WHICH CAN CAUSE INJURY AND/OR DAMAGE.
 (a) Install the lock pin (18) in the regulator valve assembly (19). NOTE : The lock pin (18) is kept in a pocket (75) on the
____ soft-cover (12) of the pack-assembly (9).
 (3) Get access to the girt bar (10) and the floor fittings (26): CAUTION : DO NOT OPEN THE PASSENGER/CREW DOOR. IF YOU DO, YOU WILL
_______ START THE SEQUENCE OF STEPS THAT PULLS THE INFLATABLE ASSEMBLY OUT OF THE PACK-ASSEMBLY.
 (a)
 Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) (4) and set the emergency control-handle (3) to the ARMED/AUTOMATIC position.

 (b)
 Carefully lift the door with the door control-handle (2).

 (c)
 Hold the door in this position, to prevent it to open fully.

 (d)
 Remove the girt bar (10): CAUTION : DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO, YOU WILL OPEN

 (e)
 Carefully lower, and lock the door with the door control-handle (2).

 (f)
 Set the emergency control-handle (3) to the DISARMED/MANUAL position, and install the SAFETY PIN - SLIDE ARMING (98D52103500000) (4).

_______ (4) Remove the pack-assembly (9) from the door:
 THE PACK ASSEMBLY.
 1_ Push the spring pawls (29), to release the girt bar (10).
 2_ Pull the girt bar (10) inboard, from the floor fittings (26).
 3_ Put the girt bar (10) on the cabin floor, inboard of the floor
 fittings (26).

 (a)
 Hold the pack-assembly (9).

 (b)
 Remove the bolts (24) and the washers (25), and keep them with the aircraft.

 (c)
 Let the pack-assembly (9) fall inboard on the supports (14), and continue to hold it.

 (d)
 Disconnect the electrical connector (15):

 -
FOR 7500MM 2871VC-A.

 -
FOR 7501MM 2870VC-A.

 -
FOR 7502MM 2873VC-A.

 -
FOR 7503MM 2872VC-A.

 (e)
 Put blanking caps on the disconnected electrical connectors.

 (f)
 Lift the pack-assembly (9) from the supports (14), and put it down carefully on the cabin floor.

 NOTE : The pack-assembly (9) weighs approximately 25.0 kg (55.12
____ lb).
 (5) Remove the girt bar (10) from the girt assembly (11): CAUTION : DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO, YOU WILL OPEN THE
_______ PACK ASSEMBLY.
 (a)
 Remove the mooring line (32) from the girt bar (10).

 (b)
 Carefully pull the girt bar (10) out of the girt assembly (11).

 (c)
 If you cannot pull the girt bar (10) out of the girt assembly (11), do these steps:

 1_ Pull open the burr-strips of the girt assembly (11).
 2_ Pull the HANDLE (31), and open the lace-up joint (34).
 3_ Remove the girt bar (10) from the opened girt assembly (11).
 4_ Keep the girt bar (10) with the door.

 EFF : 001-002, 25-62-44Page 429

Feb 01/04
R
 CES

 (6) Remove the pack-assembly (9) from the aircraft.
R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,

 Subtask 25-62-44-020-075-A
 A. Removal of the Escape-Slide raft Pack-Assembly (Ref. Fig. 402A/TASK 25-62-44-991-021-A)
 (1) Remove the decorative-cover (20) from the pack-assembly (9):
 NOTE : There are three different types of decorative-cover (20)
____ attachment:
 -
Type 1, burr-strip (Velcro).

 -
Type 2, dual-lock re-closable fastener-strip.

 -
Type 3, spring loaded latches.
 The three different types are not interchangeable.
 It is necessary to use more force, to pull apart dual-lock
 re-closable fastener-strip, than for burr-strip. You hear a
 continual click sound as the two halves are pulled apart.

 (a)
 Carefully lift the door with the door control-handle (2).

 (b)
 Hold the door in this position, to prevent it to open fully.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(115)