(5)
 Put blanking caps on the disconnected electrical connectors.

 (6)
 Remove the ELT (5):

 (a)
 Only do these steps if a programming dongle (19) is installed in the aircraft:

 (b)
 Hold the ELT (5) and release the burr-strips (velcro) on the straps (3).

 (c)
 Pull the auxiliary-antenna (4) out of the loops (25) on the straps (3).

 1_ Connect a maintenance dongle to the RCP connector (12).
 2_ Set the ON/ARM/OFF switch (10) to the ARM position for a short
 time.
 NOTE : This programs the ELT (5) with a maintenance____
 identification-data (ID). If you disconnect the
 maintenance dongle, without programming the ELT (5)
 with a maintenance ID, the ELT (5) retains its aircraft
 ID.
 3_ Set the ON/ARM/OFF switch (10) back to the OFF position.
 4_ Disconnect the maintenance dongle from the RCP connector (12).

 ELT 110MX Figure 401/TASK 25-65-35-991-001 
R  EFF :  151-199, 211-228, 301-302,  25-65-35 Page 403 Feb 01/05
 CES 

 NOTE : Be careful with the auxiliary-antenna (4), it is held in
____ the loops (25) folded back on itself. When you remove the auxiliary-antenna (4) it will move quickly back to a straight position. The auxiliary-antenna is (4) attached to the ELT (5) with the safety strap (17).
 (d) Carefully remove the ELT (5) and the auxiliary-antenna (4) from the bracket (1).

 TASK 25-65-35-400-001
 Installation of the Emergency Locator Transmitter (ELT) 110MX
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific 1 SCRAPER - NON METALLIC
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R Material No. 07-020 AI TNA 007-10012 IDENTIFICATION PAINT (Ref. 20-31-00) Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from
 the External Power 25-23-42-000-002 Removal of the Ceiling Panels - Aft Utility Area 25-23-42-400-002 Installation of the Ceiling Panels - Aft Utility Area 25-65-00-740-001 Emergency Locator Transmitter (ELT) System - BITE
 Test

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-65-00-840-001 Procedure after a Change of Aircraft Registration Number 25-65-35-991-001 Fig. 401
 3. Job Set-up
__________
 Subtask 25-65-35-860-050
 A. Aircraft Maintenance Configuration
 (1)
 Make sure the ground service network is energized (Ref. TASK 24-42-00-861-001).

 (2)
 Make sure the ceiling panel 261BC is removed (Ref. TASK 25-23-42-000-002).

 4. Procedure
_________
 Subtask 25-65-35-560-050-A
 A. Preparation for Installation
 (1) If the aircraft registration code/number (ICAO) is changed refer to (Ref. TASK 25-65-00-840-001).
 Subtask 25-65-35-420-050
 B. Installation of the ELT 110MX
 (Ref. Fig. 401/TASK 25-65-35-991-001)

 WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.

 (1) Clean the component interface and/or the adjacent area. WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(161)