-
Type 1, burr-strip.

 -
Type 2, dual-lock re-closable fastener-strip.

 -
Type 3, spring loaded latches.
 The three different types are not interchangeable.
 It is necessary to use more force, to attach the dual-lock
 re-closable fastener-strip, than for burr-strip. You can hear
 a continual click sound as the two halves are pushed together.

 EFF : 001-002, 25-62-44Page 450

Aug 01/04
R
 CES

R  (a) Types 1 and 2: 
R  1_  Align the tongues on the under side of the top edge of the
R  decorative-cover (20) with the slots (17) on the packboard 
R  (13). 
R  2_  Press the top edge of the decorative-cover (20) on to the
R  attach-strips (16). 
R  3_  Push the lower edge of the decorative-cover (20) against the
R  pack-assembly (9) until the spring clips engage. 
R  (b) Type 3: 
R  1_  Engage the spring loaded bolts (73).
R  2_  Push the lower edge of the decorative-cover (20) against the
R  pack-assembly (9) until the spring clips engage. 
R  (c) Make sure that you can see the gage through the hole in the 
R  decorative-cover (20). 
R  (6) Do a visual inspection of the visual indicator (30), and its related 
R  ARMED indication: 
R  (Ref. Fig. 406/TASK 25-62-44-991-017) 
R  (a) Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) (4) and set 
R  the emergency control-handle (3) to the ARMED/AUTOMATIC position. 
R  (b) If installed, make sure that the self-adhesive placards are in a 
R  good condition. 
R  1_  If necessary install new self-adhesive placards (Ref. TASK 11-
R  00-00-400-007) and (Ref. AMM 11-32-52 P. Block 001). 
R  2_  Make sure that the point of the self-adhesive arrow (67),
R  aligns with the RED mark. 
R  3_  If not, re-position the self-adhesive arrow (67).
R  (c) It is not necessary to make adjustments on aircraft where an 
R  ARMED/AUTOMATIC placard (68) is installed on the cabin floor. 
R  (d) Set the emergency control-handle (3) to the DISARMED/MANUAL 
R  position, and install the SAFETY PIN - SLIDE ARMING 
R  (98D52103500000) (4). 
R 

 Installation Procedure of the Girt Bar Figure 405A/TASK 25-62-44-991-019-A13 (SHEET 1) 
R  EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,  25-62-44 Page 452 Aug 01/05
 CES 

 Installation Procedure of the Girt Bar Figure 405A/TASK 25-62-44-991-019-A23 (SHEET 2) 
R  EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,  25-62-44 Page 453 Aug 01/05
 CES 

 Installation Procedure of the Girt Bar Figure 405A/TASK 25-62-44-991-019-A33 (SHEET 3) 
R  EFF : 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,  25-62-44 Page 454 Aug 01/05
 CES 

R  Visual Indicator - Adjustment Figure 406/TASK 25-62-44-991-017
 EFF :  ALL  25-62-44 Page 455 May 01/04
 CES 

R  **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 25-62-44-420-062-A
 C. Installation of the Escape-Slide Raft Pack-Assembly
 (Ref. Fig. 402A/TASK 25-62-44-991-021-A)

 (1) Install the girt bar (10) in the girt assembly (11): CAUTION : DO NOT PULL THE GIRT ASSEMBLY. IF YOU DO, YOU WILL OPEN THE
_______
 PACK ASSEMBLY.

 (a)
 Pull open the burr-strips of the girt assembly (11).

 (b)
 Pull the HANDLE (31), and open the lace-up joint (34).

 (c)
 Refer to the FIGURE for the correct procedure. (Ref. Fig. 405A/TASK 25-62-44-991-019-A)

 NOTE : Safety the parachute-pin in position with nylon cord, that
____ has a minimum breaking strain of 9.0 lb (4.0823 kg).
 (2) Install the pack-assembly (9) on the door:
 (a)
 Remove the blanking caps from the electrical connectors.

 (b)
 Make sure that the electrical connectors are clean and in the correct condition.

 (c)
 Lift the pack-assembly (9) on the supports (14). NOTE : The pack-assembly (9) weighs approximately 50.0 kg (110.23

____
 lb).

 (d)
 Hold the pack-assembly (9) at an angle inboard, on the supports (14).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備4(121)