EFF : 301-399, 25-62-48Page 415
Nov 01/04
R
CES 4. Procedure
_________ Subtask 25-62-48-020-050
A. Removal of the Emergency Escape-Slide Release-Mechanism Assembly
(Ref. Fig. 403/TASK 25-62-48-991-003)
(1) Remove the release-mechanism control-cable assembly (9) (refer to as the control cable):
(a)
Remove and discard the cotter pin (13).
(b)
Remove the pin (11), the washers (12) and (10), and disengage the eye-end of the control cable (9) from the override clutch (14).
(c)
Remove and discard the cotter pin (53).
(d)
Remove the pin (51), the washers (52) and (56), and disengage the other eye-end of the control cable (9) from the lever assembly (54).
(e)
Remove and discard the lockwire from the locknuts (63) and (64).
(f)
Loosen the locknuts (63) and (64).
(g)
Remove the nuts (59), the screws (61), the washers (60) and the clamps (62) from the door-frame structure.
NOTE : Do not remove the clamps (62) from the control cable (9).
____
(h) Disengage the control cable (9) from the brackets (65) and remove it.
(2) Remove the release-mechanism rod-assembly (46) (refer to as the rod assembly):
(a)
Remove and discard the cotter pin (42).
(b)
Remove the pin (40) and the washer (41), and disengage the rod assembly (46) from the release lever (43).
(c)
Remove and discard the cotter pin (50).
(d)
Remove the pin (48) and the washer (49), disengage the rod assembly (46) from the lever assembly (54) and remove it.
EFF : 301-399, 25-62-48Page 416
Nov 01/04
R
CES
(3)
Remove the override clutch:
(a)
Remove the SAFETY PIN - SLIDE RELEASE LEVER (27) from the related rigging hole of the lever (28).
(b)
Remove the dome nut (30) and the washer (29).
(c)
Remove the lever (28) and the sleeve (26) from the shaft (16).
(d)
Remove the screws (22) and (25), and the washers (21) and (24).
(e)
Remove the stop-screw (23) and the bearing-assembly (18).
(f)
Remove the spring element (17) from the bearing-assembly (18).
(g)
Hold the spacers (7) and the sleeve (8).
(h)
Carefully pull the shaft (16) through the door-frame structure out of the bearing-assembly (6) until you can remove the spacers
(7) and the sleeve (8).
(i)
Hold the override clutch (14).
(j)
Carefully continue to pull the shaft (16) through the door-frame structure until you can easily remove the override clutch (14).
(k)
Fully remove the shaft (16) through the door-frame structure.
(4)
Remove the screws (4), the washers (5) and the bearing assembly (6).
EFF : 301-399, 25-62-48Page 417
Nov 01/04
R
CES TASK 25-62-48-400-001
Installation of the Emergency Escape-Slide Release-Mechanism Assembly
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific clean cloth
No specific feeler gage
No specific nonmetallic scraper
No specific warning notice(s)
No specific access platform(s) 3.4 m (11 ft. 2 in.)
98D52207551000 1 SAFETY PIN - SLIDE RELEASE LEVER
98D52207552000 1 RIGGING PIN - SLIDE RELEASE MECHANISM
98D52207553000 1 RIGGING PIN - SLIDE RELEASE MECHANISM
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific cotter pin-corrosion resistant steel MS24665-151 No specific washer AN960C616 No specific washer AN960C616L No specific washer AN960C616LL Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00) Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
Material No. 09-019 USA AMS 3267/3
LOW ADHESION CORROSION INHIBITING SEALANT
(Ref. 20-31-00)
R Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM EQUIPMENT/FURNISHINGS 設(shè)備4(137)
