(2)
Put the safety barriers in position.
Subtask 57-53-00-860-084
B. Aircraft Maintenance Configuration
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1) Fully extend the flaps (Ref. TASK 27-50-00-866-008).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 660 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
Subtask 57-53-00-865-089
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 57-53-00-010-058
D. Get Access
(1)
Put the access platform below the applicable trailing edge at flap track 3, zone 532(632).
(2)
Remove the applicable access panels (Ref. TASK 57-55-11-000-001):
-
for the left wing, remove 532AT, 532CB
-
for the right wing, remove 632AT, 632CB.
4. Procedure
_________
(Ref. Fig. 609/TASK 57-53-00-991-010)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-53-00-110-057
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the flap link arm and the fairing operating arm.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 661 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Outboard Flap - Drive Linkage and Drive Fitting - Location
Figure 609/TASK 57-53-00-991-010
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 662 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Subtask 57-53-00-210-058
B. Inspection
(1) Examine the flap link arm and the fairing operating arm. Make sure that:
-
there is no corrosion
-
there are no cracks
-the protective treatment is in the correct condition. NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____
correct repair procedure.
5. Close-up
________ Subtask 57-53-00-865-090
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-410-057
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. TASK 57-55-11-400-001):
-for the left wing, install 532AT, 532CB
-for the right wing, install 632AT, 632CB. Subtask 57-53-00-860-085
C. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Fully retract the flaps (Ref. TASK 27-50-00-866-009).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 663 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Subtask 57-53-00-942-058
D. Removal of Equipment
(1)
Remove the access platform(s).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(82)
