Subtask 57-52-00-865-076
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 654 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-52-00-010-062

 D. Get Access
 (1) Put the access platform below the applicable wing trailing edge at the inboard flap trunnion attachment, zone 581(681).
 4. Procedure
_________ (Ref. Fig. 610/TASK 57-52-00-991-010) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 Subtask 57-52-00-280-056
 A. Inspection
 (1) Do a special detailed inspection of the trunnion attachment bracket and the inboard trunnion LH/RH (Ref. NTM 57-52-03 PART 9).
 NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie.
 5. Close-up
________ Subtask 57-52-00-410-062
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 Subtask 57-52-00-865-077
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 655 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Inboard Flap - Trunnion Attachment Bracket - Detail
 Figure 610/TASK 57-52-00-991-010

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 656 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-52-00-860-100

 C. Aircraft Maintenance Configuration
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.

 (3) Retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-52-00-942-063
 D. Removal of Equipment
 (1)
 Remove the access platform(s).

 (2)
 Remove the warning notice(s).

 (3)
 Remove the safety barriers.

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-52-00Page 657 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

R

R
R

**ON A/C ALL
 TASK 57-52-00-220-007
 Special Detailed Inspection of Outer Wing Inboard Flap Track 2 Flap Pivot Bolt Assembly
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 575252-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notices No specific access platform 2.5 m (8 ft. 2 in.) No specific Torque Wrench : range 2.00 to 20.00 m.daN
 (15.00 to 150.00 lbf.ft) 98D27504083000 1 EXTRACTOR - PIN TRACKS 2 AND 3 98D27504084000 1 EXTRACTOR - PIN 98D27504111000 1 SLAVE PIN-TRACK 2 & 3 98D27504112000 1 SLAVE PIN-TRACK 4 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(26)