(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the correct dimensions, to make new covers for the inspection holes.
(3)
Install the new cover on the applicable inspection hole.
(4)
Install the leading edge panel 2 (Ref. TASK 27-54-62-400-003).
(5)
Install the flap track 3 fairing 532CB (632CB) and the access panel 532AT (632AT) (Ref. TASK 57-55-11-400-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 630 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 057-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-53-00-410-053-A
A. Close Access
(Ref. Fig. 605A/TASK 57-53-00-991-006-A)
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the correct dimensions, to make new covers for the inspection holes.
(3)
Install the new cover(s) on the applicable inspection hole(s).
(4)
Install the flap track 3 fairing 532CB (632CB) and the access panel 532AT (632AT) (Ref. TASK 57-55-11-400-001).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-53-00-865-060
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-103
C. Aircraft Maintenance Configuration
(1) Retract the flaps fully (Ref. TASK 27-50-00-866-009).
Subtask 57-53-00-942-054
D. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 631 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
TASK 57-53-00-200-005
Detailed Inspection of Outboard Flap Support at Track 3, including RIB5, Fitting Assembly and Attachment Structure, Internal and External, LH/RH
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575309-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 2.5 m (8 ft. 2 in.)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 632 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A D DAN 220
ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(75)
