(2)
Put the safety barriers in position.
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-52-00Page A673 1 1 May 01/05 1 1 1CES 1 Subtask 57-52-00-860-105
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Fully extend the flaps (Ref. TASK 27-50-00-866-008).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever.
(3)
Put the access platform below the applicable flap track 1, zone 500(600).
Subtask 57-52-00-865-111
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 57-52-00-010-085
D. Get Access
(1)
Open the applicable MLG door 734, 744 (Ref. TASK 32-12-00-010-001).
(2)
Make sure that the GROUND LOCK SLEEVE (460005835) is installed on the applicable MLG door actuator.
(3)
Remove the applicable access panels (Ref. TASK 53-35-11-000-001):
-
for the LH wing, remove 193AB, 193BB
-
for the RH wing, remove 194AB, 194BB.
(4)
Remove the applicable flap track 1 actuator (Ref. TASK 27-54-49-000-001).
(5)
Disconnect the applicable flap track 1 actuator drive lever from the applicable flap link arm (Ref. TASK 27-54-55-000-001).
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-52-00Page A674 1 1 May 01/05 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 629/TASK 57-52-00-991-031) Subtask 57-52-00-100-050
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the component interface and the adjacent area.
Subtask 57-52-00-200-052
B. Detailed Visual Inspection of the Actuator Lever Bushes and Actuator Splines
(1)
Before you do the inspection, move the actuator lever to approximately the 20 deg. flap position.
(2)
Inspect the actuator lever bushes for wear:
(a) Measure the sideplay of the actuator lever:
1_ If the dimension X is less than 2.40 mm (0.0944 in.) and there
is no wear or corrosion of the actuator output-shaft splines,
the actuator is in a serviceable condition.
2_ If the dimension X is between 2.40 mm (0.0944 in.) and 3.80 mm
(0.1496 in.), refer to (Ref. ISB 57-1108).
3_ If the dimension X is more than 3.80 mm (0.1496 in.), or the
actuator output-shaft splines are more than 50% corroded,
refer to AIRBUS INDUSTRIE for instructions.
Subtask 57-52-00-865-112
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-52-00Page A675 1 1 May 01/05 1 1 1CES 1
Flap Track 1 Actuator and Drive Lever - Inspection Area
Figure 629/TASK 57-52-00-991-031- 12 (SHEET 1)
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-52-00Page A676 1 1 May 01/05 1 1 1CES 1
Flap Track 1 Actuator and Drive Lever - Inspection Area
Figure 629/TASK 57-52-00-991-031- 22 (SHEET 2)
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-52-00Page A677 1 1 May 01/05 1 1 1CES 1
5. Close-up
________
Subtask 57-52-00-410-088
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(57)
