(2)
Disconnect the inboard flap from the flap track 2 carriage (Ref. TASK 27-54-61-000-001). Do not remove the end stop from the flap track.
(3)
Move the carriage along the flap track, until you can get clear access to the carriage forging.
(4)
Use a clamp to hold the carriage in position on the flap track. Use a protective pad to prevent damage to the flap track surfaces.
**ON A/C 301-399,
Subtask 57-52-00-010-056-A
D. Get Access
(1)
Lower the flap track 2 fairing (Ref. TASK 57-55-11-010-001).
(2)
Disconnect the inboard flap from the flap track 2 carriage (Ref. TASK 27-54-61-000-003). Do not remove the end stop from the flap track.
(3)
Move the carriage along the flap track, until you can get clear access to the carriage forging.
(4)
Use a clamp to hold the carriage in position on the flap track. Use a protective pad to prevent damage to the flap track surfaces.
**ON A/C ALL
4. Procedure
_________ (Ref. Fig. 605/TASK 57-52-00-991-005) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-52-00-110-057
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the carriage forging.
Subtask 57-52-00-210-053
B. Inspection
(1) Examine the carriage forging. Make sure that:
-
there is no corrosion
-
there are no cracks
-the surface protection is in the correct condition.
1EFF : ALL 1 57-52-00Page 626 1 1 May 01/05R 1 1 1CES 1
Inboard Flap Track 2 - Carriage Forging - Location Figure 605/TASK 57-52-00-991-005
1EFF : 1 1R 1CES ALL 1 11 1 57-52-00 Page 627 Aug 01/99
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-52-00-410-056
A. Close Access
(1)
Remove the clamp and the protective pad from the flap track.
(2)
Connect the inboard flap to the flap track 2 carriage (Ref. TASK 27-54-61-400-001).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4) Lift the flap track 2 fairing (Ref. TASK 57-55-11-410-001).
**ON A/C 301-399,
Subtask 57-52-00-410-056-A
A. Close Access
(1)
Remove the clamp and the protective pad from the flap track.
(2)
Connect the inboard flap to the flap track 2 carriage (Ref. TASK 27-54-61-400-003).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4) Lift the flap track 2 fairing (Ref. TASK 57-55-11-410-001).
**ON A/C ALL
Subtask 57-52-00-865-065
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-52-00-860-086
C. Aircraft Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Retract the flaps (Ref. TASK 27-50-00-866-009).
(3) Retract the spoilers (Ref. TASK 27-60-00-866-002). Subtask 57-52-00-942-057
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-52-00Page 629 1 1 May 01/05R 1 1 1CES 1
TASK 57-52-00-220-004
Special Detailed Inspection of Outer Wing Inboard Flap Track 2 Carriage Forging
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(19)
