曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  581(681). 
R  (2) Remove and discard the covers to the inspection holes in the bottom 
R  skin each side of Rib 6. 
R  (3) Make sure that the applicable inspection holes are clear of unwanted 
R  material. 
R  4. Procedure_________ 
R  (Ref. Fig. 627/TASK 57-52-00-991-027) 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______ 
R  EDGE: 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  Subtask 57-52-00-280-061 
R  A. Inspection 
R  (1) Do a special detailed inspection of the Rib 6 of the inboard double 
R  slotted flap LH/RH (Ref. NTM 575241 PART 9). 
R  NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____ 
R  correct repair procedure. If the defect is not included in 
R  this repair, you must request a procedure from Airbus 
R  Industrie. 
R  5. Close-up________ 
R  Subtask 57-52-00-410-080 
R  A. Close Access 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A), cut to the 
R  correct dimensions, to make new covers for the inspection holes.

 

R Inboard Flap - Rib 6 - Inspection Area
R Figure 627/TASK 57-52-00-991-027- 12 (SHEET 1)

 1EFF : 301-399, 1 57-52-00Page A658 1 1 May 01/04 1 1 1CES 1

R Inboard Flap - Rib 6 - Inspection Area
R Figure 627/TASK 57-52-00-991-027- 22 (SHEET 2)

 1EFF : 301-399, 1 57-52-00Page A659 1 1 May 01/04 1 1 1CES 1

R  (3) Install the new covers on the inspection holes. 
R  Subtask 57-52-00-865-110 
R  B. Remove the safety clip(s) and the tag(s) and close this(these) circuit 
R  breaker(s): 
R  6CV, 8CV. 
R  Subtask 57-52-00-860-076 
R  C. Aircraft Maintenance Configuration 
R  (1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat 
R  control lever. 
R  (2) Retract the flaps (Ref. TASK 27-50-00-866-009). 
R  Subtask 57-52-00-942-079 
R  D. Removal of Equipment 
R  (1) Remove the access platform(s). 
R  (2) Remove the safety barriers. 
R  (3) Remove the warning notice(s). 
R  (4) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

R **ON A/C ALL

 TASK 57-52-00-220-015
 Detailed Dimensional Check of the Joints that Attach the Flap to the Flap Carriage (Tracks 1 and 2)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Because the free movement of the inboard flap is more than that in TASK 27-54-00-200-003.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific access platform 2 m (6 ft. 7 in.)

 B. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-54-61-000-001 Removal of the Inboard Flap
 27-54-61-000-003 Removal of the Inboard Double-Slotted Flap
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(53)