(3)
Do a manual extension of the spoilers (Ref. TASK 27-60-00-866-002).
(4)
Make sure that the COLLAR-SAFETY, SPOILER is installed on the applicable spoiler actuator.
(5)
Put the adjustable access platform below the applicable wing traling edge at flap track 2, zone 531(631).
1EFF : ALL 1 57-52-00Page 637 1 1 May 01/04R 1 1 1CES 1
Subtask 57-52-00-865-068
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure
_________ (Ref. Fig. 607/TASK 57-52-00-991-007) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-52-00-110-059
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the drive lever.
Subtask 57-52-00-210-054
B. Inspection
(1)
Make a detailed visual inspection of the outer wing inboard flap track 2 drive lever.
(2)
Examine the flap track 2 drive lever. Make sure that:
-
there is no corrosion or damage
-
there are no cracks
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the
____
correct repair procedure.
1EFF : ALL 1 57-52-00Page 638 1 1 May 01/04R 1 1 1CES 1
Inboard Flap Track 2 - Drive Lever Figure 607/TASK 57-52-00-991-007
1EFF : 1 1R 1CES ALL 1 11 1 57-52-00 Page 639 May 01/04
5. Close-up
________ Subtask 57-52-00-865-069
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-52-00-860-088
B. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Do a manual retraction of the spoilers (Ref. TASK 27-60-00-866-002).
(3) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-52-00-942-059
C. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-52-00Page 640 1 1 May 01/04R 1 1 1CES 1
TASK 57-52-00-220-005
Special Detailed Inspection of Outer Wing Inboard Flap Track 2 Drive Lever
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575254-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 2.5 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(22)
