(4)
 Install the new cover(s) on the applicable inspection hole(s).

R **ON A/C 106-149, 215-299, 301-399, 401-499,
 Subtask 57-52-00-210-068-A
 A. Inspection of Inboard Flap, Bottom Surface, Drain Holes and Inspection Holes
 (1)
 Examine the inboard flap, bottom surface drain holes. Make sure that:

 -there are no rubber grommets installed in the drain holes
 -the drain holes are not blocked.

 (2)
 If a drain hole is blocked, remove all unwanted material from around the hole. Use a 5.0mm (0.2 in.) dia. non-metallic probe to remove the blockage from the hole.

 (3)
 Examine the inboard flap, bottom surface inspection holes. Make sure that:

 -
the rubber grommets are correctly installed in each inspection hole

 -
the rubber grommets are in good condition.

 Subtask 57-52-00-960-050-A
 B. Replace Defective or Missing Inspection Hole Rubber Grommets
 (1)
 Remove and discard the damaged inspection hole rubber grommet(s).

 (2)
 Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the internal surfaces of the applicable inboard flap, bottom surface inspection hole(s).

R (3) Install the new rubber grommet(s) in the applicable inspection R hole(s).
 **ON A/C ALL
 5. Close-up
________
 Subtask 57-52-00-865-116

 A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 122VU FLIGHT CONTROLS/WTB/FLP/SYS1 10CV S07
 Subtask 57-52-00-860-110
 B. Aircraft Maintenance Configuration
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Retract the flaps fully (Ref. TASK 27-50-00-866-009).
 Subtask 57-52-00-942-083

 C. Removal of Equipment
 (1)
 Remove the access platform(s).

 (2)
 Remove the warning notice(s).

 (3)
 Remove the safety barriers.

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 SKINS AND PLATING - CLEANING/PAINTING
_____________________________________
 TASK 57-52-11-100-001
 Inboard Flap - Cleaning / Painting
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR. 
R R R R R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job__________________
 Self Explanatory
 2. Job Set-up Information______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific No specific No specific  safety barrierssoft brushvacuum cleanerwarning noticeswash brushaccess platform 2 m (6 ft. 7 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-001 USA MIL-D-16791 TYPE I
 DETERGENT (Ref. 20-31-00)
 Material No. 11-026 GB DEF-STAN 68-148/1
 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
 Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground
 27-50-00-866-009 Retraction of the Flaps on the Ground
 51-75-12-300-001 Repair of Major Paint Damage on Light Alloy and
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼4(61)