(2)
Carefully move the door in its installation position.
(3)
Connect the door on the support arm as follows:
(a)
Make sure that the upper and lower connection forks (62) and (76) of the support arm engage with the lifting lever (88) and the control lever (74).
(b)
Install the upper hinge bolt (68) on the lifting lever (74) as follows:
1_ Put the bracket (89) and the adjustment washers (66) in
position and install the bushes (70) into the spacer tube
(65),
2_ Install the hinge bolt (68) , the washers (69) and the nuts
(72) at the fork-end (71),
NOTE : The hinge bolt (68) must go in smoothly.____
3_ Safety the nut (72) with the new cotter pin (73).
1EFF : 301-399, 1 52-22-11Page 419 1 1 May 01/04 1 1 1CES 1 (c) Install the lower hinge bolt (82) on the control lever (88) as follows:
1_ Put the bracket (90) and the adjustment washers (80) in
position and install the bushes (84) into the spacer tube
(79).
2_ Install the hinge bolt (82) , the washers (83) and the nuts
(86) at the fork-end (85).
NOTE : The hinge bolt (82) must go in smoothly.____
3_ Safety the nut (86) with the new cotter pin (87).
Subtask 52-22-11-820-051
E. Adjustment of the Parallel Motion
(1)
Carefully move the door in its half-open position.
(2)
Measure the distances between the door edges and the outer skin of the fuselage.
NOTE : The distances must be the same. The tolerance is 2.0 mm
____ (0.0787 in.) maximum.
(3)
If the tolerance is more than is permitted, push the door manually to the correct position.
(4)
If it is not possible, adjust the position of the related attachment fitting mounted on the door frame.
Subtask 52-22-11-420-052
F. Final Installation
(1) Attach the upper guide arm (35) on the guide fitting (33) as follows: (Ref. Fig. 403/TASK 52-22-11-991-003)
(a)
Release the upper guide arm (35) from the door frame.
(b)
Install the bush (34) in the guide fitting (33).
(c)
Connect the eye-end of the upper guide arm (35) in the related fork-end of the guide fitting (33)
1EFF : 301-399, 1 52-22-11Page 420 1 1 May 01/04 1 1 1CES 1
(d) Install the bush (37), the bolt (31), the washers (32) and the nut (38).
NOTE : The bolt (31) must go in smoothly.
____
(e)
If not, adjust the position of the related attachment fitting mounted on the door frame.
(f)
Tighten the nut (38) and safety it with the new cotter pin (39).
(2)
Connect the sliding sleeve (50) on the door attachment fitting (46) as follows: (Ref. Fig. 404/TASK 52-22-11-991-004)
(a)
Put the fork-end of the sliding sleeve (50) on the traverse (55) and install the spacer sleeve (54).
(b)
Install the bolt (53), the washers (49) and the nut (48) on the sliding sleeve (50).
(c)
TORQUE the nut (48) to to 0.59 m.daN (52.21 lbf.in) and safety it with the new cotter pin (47).
(3)
Install the wire harness (18) and the bonding straps (23) between the door and the support arm as follows: (Ref. Fig. 402/TASK 52-22-11-991-002)
(a)
Install the bonding straps (23) with the bolts (21), the washers
(22) and the nuts (24) on the support arm (15) (Ref. TASK 20-28-00-912-004).
(b)
Connect the connector (11) of the wire harness (18) to the receptacle (12) of the door damper (refer to the subsequent table).
---------------------------------------------------------| DOOR | CONNECTOR | DOOR DAMPER | FRAME | CABLE LOOM | _________________________________________________________
| FWD LH | 360RH5-A | 1600WM | FR35 | 4251VB |
| FWD RH | 360RH6-A | 1601WM | FR35 | 4250VB |
| AFT LH | 360RH7-A | 1602WM | FR47.2| 4253VB |
| AFT RH | 360RH8-A | 1603WM | FR47.2| 4252VB |
---------------------------------------------------------
(c) Install the clamps (19) with the screws (20), the washers (16) and the nuts (17) on the support arm (15).
1EFF : 301-399, 1 52-22-11Page 421 1 1 May 01/04 1 1 1CES 1
(d) Measure a distance "A" at the wire harness (18) between the last clamp (19) of the support arm (15) and the first clamp (25).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(85)
