(3) If the distance "U" is out of tolerance, adjust the position of the stop bolt (64) as follows:
 (a) If required, bend the tab washer (66) to release the adjustment nut (65).
 NOTE : In this case, replace the tab washer (66).
____
 (b)
 Loosen the jam nut (68) and the adjustment nut (65).

 (c)
 Turn the stop bolt (64) as required until the distance "U" is correct.

 (d)
 Tighten the adjustment nut (65) and the jam nut (68).

 (e)
 Safety the adjustment nut (65) with the tab washer (66).

 5. Close-up
________ Subtask 52-22-14-865-052
 A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 153RH
 Subtask 52-22-14-410-050
 B. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Do the special precaution for the door damper and emergency operation cylinder (Ref. TASK 52-22-00-860-004).

 (3)
 Close applicable the door (Ref. TASK 52-22-00-410-001).

 (4)
 Remove the access platform(s).

 1EFF : 301-399, 1 52-22-14Page 410 1 1 May 01/04 1 1 1CES 1

 TASK 52-22-14-000-002 Removal of the Telescopic Rod Assembly
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  access platform 3.2 m (10 ft. 6 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-22-00-010-001  Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder 52-22-14-991-002 Fig. 403
 3. Job Set-up
__________ Subtask 52-22-14-010-051
 A. Get Access
 (1)
 Partly open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).

 (2)
 Make sure that the access platform is in position below the partly opened door.

 (3)
 Make sure that the special precaution procedure for the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).

 1EFF : 301-399, 1 52-22-14Page 411 1 1 May 01/04 1 1 1CES 1

 4. Procedure
_________
 (Ref. Fig. 403/TASK 52-22-14-991-002) Subtask 52-22-14-020-051
 A. Removal of the Telescopic Rod Assembly
 (1)
 Disconnect the telescopic rod assembly (57) from the yoke assembly

 (52)
 as follows:

 (a)
 Remove and discard the cotter pin (48) from the nut (49).

 (b)
 Remove the nut (49) and the washer (50) from bolt (54).

 (c)
 Remove the bolt (54) and the washer (53) from the yoke assembly (52).

 (d)
 Hold the piston of the door damper (55) and disassemble the fork-end (56) from the yoke assembly (52).

 (e)
 If neceesary, remove the bush (51) from the yoke assembly (52).

 (2)
 Disconnect the telescopic rod assembly (57) from the door fitting

 (35)
 as follows:

 (a)
 Remove and discard the cotter pin (41) from the nut (42).

 (b)
 Remove the nut (42), the washer (43), tab plate (44), the washer

 (47) and the bolt (46).
 NOTE : Remove lock plate (59) if installed as an alternative to

____ the washer (43) and the tab plate (44).
 (c)
 Hold the telescopic rod assembly (57) and carefully remove the spacer (45) from the sliding sleeve (58).

 (d)
 Disassemble the sliding sleeve (58) from the transversal link (40).

 (3) If necessary, remove the transveral link (40) from the door fitting
 (35)
 as follows:

 (a)
 Remove and discard the cotter pin (31) from the nut (32).

 (b)
 Remove the nut (32) and the washer (33) from the transversal link (40).

 1EFF : 301-399, 1 52-22-14Page 412 1 1 May 01/04 1 1 1CES 1

 Telescopic Rod Assembly
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(103)