R Installation of the Rigging pin
R Figure 516/TASK 52-22-00-991-021
1EFF : 301-399, 1 52-22-00 Page 555
1 1 May 01/04
1 1
1CES 1
R Adjustment of Slide Release Mechanism
R Figure 517/TASK 52-22-00-991-023- 13 (SHEET 1)
1EFF : 301-399, 1 52-22-00Page 556 1 1 May 01/04 1 1 1CES 1
R Adjustment of Slide Release Mechanism
R Figure 517/TASK 52-22-00-991-023- 23 (SHEET 2)
1EFF : 301-399, 1 52-22-00Page 557 1 1 May 01/04 1 1 1CES 1
R Adjustment of Slide Release Mechanism
R Figure 517/TASK 52-22-00-991-023- 33 (SHEET 3)
1EFF : 301-399, 1 52-22-00Page 558 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 559 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 560 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 561 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 562 1 1 May 01/04 1 1 1CES 1
R (2) If the distance "L" is out of tolerance, adjust the length of spring
R rod assy (191) as follows:
R (a) Cut and remove the cotter pin (196) from the pin (198).
R (b) Remove the washer (197) and the pin (198) and disconnect the
R upper eye-end (195) from the lever (199).
R (c) If required, cut and remove the lockwire and loosen the jam nut
R (193).
R (d) Turn the upper eye-end (195) until the distance "L" is correct.
R (e) Tigthen the jam nut (193) and safety it with the lockwire,
R corrosion resistance steel, dia 0.8 mm (0.30 in.) on the locking
R devices (194).
R (f) Put the upper eye-end (195) in position to the lever (199) and
R attach it with the pin (198) and the washer (197).
R (g) Safety the pin (198) with the new cotter pin (196).
R (3) Measure the distance "M" between the guide fitting (190) and the
R retainer cap (191).
R NOTE : The distance "M ust be 38.0 mm (1.4960 in.).____
R (4) If the distance "M" is out of tolerance, adjust the spring rod assy
R (192) as follows:
R (a) If required, cut and remove the lockwire and loosen the jam nut
R (189).
R (b) Turn the lower eye-end (188) until the distance "M" is correct.
R (c) Tigthen the jam nut (189) and safety it with the lockwire,
R corrosion resistance steel, dia 0.8 mm (0.30 in.) on the locking
R devices (194).
R (5) Make sure that there is no play at the slide control handle (187).
R (6) If there is a play at the slide control handle (187), adjust the
R length of the connection rod (180) as follows:
R (a) If required, cut and remove the lockwire and loosen the jam nuts
R (182).
R (b) Turn the rod (183) until there is no play at the slide control
R handle (187).
R (7) Adjust the indication of the arm/disarm unit as follows:
R (a) Make sure that the slide control handle (187) is moved up in the
R disarmed position.
R (b) Make sure that the green " DISARMED " label (186) is in the
R center of the indication plate (184).
R (c) If not, replace the self-adhesive green "DISARMED" label (186) so
R that it is in the correct center position of the indication plate
R (184).
R (d) Move down the slide control handle (187) in the armed position.
R (e) Carefully mark the position of the red "ARMED" label (185) in the
R center of the indication plate (184).
R (f) Put the self-adhesive red "ARMED" lable (185) in the correct
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(76)
