(a)
 Remove and discard the cotter pin (164) from the pin (167).

 (b)
 Remove the washer (165) and the pin (167) from the joint (168).

 (c)
 Remove the indication lever (166) from the joint (168).

 (d)
 Hold the locking indicator assembly (160) and remove the nuts

 (161) and the bolts (162).

 (e)
 Remove the locking indicator assembly (160) from the door structure.

 (2)
 Disconnect the push rod (190) from the engaging lever (184) as follows:

 (a) Remove and discard the cotter pin (187) from the nut (188).
 1EFF : 301-399, 1 52-22-21Page 430 1 1 May 01/04 1 1 1CES 1

 (b)
 Remove the nut (188), the washers (189), the bush (191) and the bolt (193) from the engaging lever (184).

 (c)
 Disconnect the eye-end of the push rod (190) from the fork-end of the engaging lever (184).

 (d)
 If required, remove the bush (192) from the fork-end of the engaging lever (184).

 (3)
 Disconnect the actuation rod (197) from the engaging lever (184) as follows:

 (a)
 Remove and discard the cotter pin (186) from the nut (185).

 (b)
 Remove the nut (185), the washers (183), the bush (195) and the bolt (182) from the engaging lever (184).

 (c)
 Disconnect the eye-end of the actuation rod (197) from the fork-end of the engaging lever (184).

 (d)
 If required, remove the bush (196) from the fork-end of the engaging lever (184).

 (4)
 Disconnect the connection rod (118) from the actuation lever (123) as follows:

 (a)
 Remove and discard the cotter pin (124) from the nut (125).

 (b)
 Remove the nut (125), the washers (121), the bush (119) and the bolt (122) from the actuation lever (123).

 (c)
 Disconnect the eye-end of the connection rod (118) from the fork-end of the actuation lever (123).

 (d)
 If required, remove the bush (120) from the fork-end of the actuation lever (123).

 (5)
 Disconnect the fork link (139) from the twin lever (152) as follows:

 (a)
 Remove and discard the cotter pin (141) from the nut (142).

 (b)
 Remove the nut (142), the washers (143), the bush (144) and the bolt (147) from the fork link (139).

 (c)
 Disconnect the fork link (139) from the twin lever (152) and support the spacer (145).

 1EFF : 301-399, 1 52-22-21Page 431 1 1 May 01/04 1 1 1CES 1

 Locking Shaft Assembly (60" Door)
 Figure 405/TASK 52-22-21-991-004- 12 (SHEET 1)

 1EFF : 301-399, 1 52-22-21Page 432 1 1 May 01/04 1 1 1CES 1

 Locking Shaft Assembly (60" Door)
 Figure 405/TASK 52-22-21-991-004- 22 (SHEET 2)

 1EFF : 301-399, 1 52-22-21Page 433 1 1 May 01/04 1 1 1CES 1

 (d) If required, remove the bush (146) from the fork link (139).
 (6) Disconnect the spring unit (154) from the twin lever (152) as
 follows:

 WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE
_______ TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
 (a)
 Remove and discard the cotter pin (149) from the nut (148).

 (b)
 Remove the nut (148), the washers (150), the bushes (153) and the bolt (151) from the twin lever (152).

 (c)
 Disconnect the eye-end of the spring unit (154) from the fork-end of the twin lever (152).

 (7)
 Disconnect the spring rod assembly (179) from the indication lever

 (166) as follows:
 WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE

_______ TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
 (a)
 Remove and discard the cotter pin (181) from the pin (178).

 (b)
 Remove the washer (180) and the pin (178) from the indication lever (166).

 (c)
 Disconnect the fork-end of the spring rod assemby (179) from the indication lever (166).

 (8)
 Disconnect the support fitting (177) from the door structure as
 follows:

 (a)
 Remove the nuts (198) and (200) from the bolts (199), (207) and (209).

 (b)
 Remove the bolts (207) and (209) and disconnect the stop fitting

 (208) from the support fitting (177).

 (c)
 Remove the bolts (199) and (207) to disconnect the support fitting (177) from the door structure.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(119)