(b)
Make sure that the slide control handle is lowered and the escape slide-release mechanism is in the DISARMED mode.
NOTE : The indication window must show DISARMED in green.
____
(c) Install the PIN - SAFETY SLIDE (98A52107632000) to safety the slide control handle in its lowered position.
(3) Install the lock pin on the inflation reservoir as follows:
(a)
Open the access door of the overhead stowage compartment above the applicable door.
(b)
Loosen the quick-release fasteners and remove the rear inside fairing of the applicable overhead stowage compartment.
(c)
Remove the lock pin from the stowage pocket of the inflation reservoir.
(d)
Install the lock pin on the operation valve to prevent the accidental inflation of the escape slide below the applicable door.
NOTE : On the CICS programming and test panel 110RH the
____ indication "SLIDE PRESS LOW" which is only simulated in this case comes on.
1EFF : 301-399, 1 52-22-00Page 212 1 1 May 01/04 1 1 1CES 1 TASK 52-22-00-410-002
Closing of the Emergency Exit Doors from the Outside
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.20 m (10 ft. 6 in.) 98A52107632000 1 PIN - SAFETY SLIDE 98D52207551000 1 SAFETY PIN - SLIDE RELEASE LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the
External Power 52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-410-001 Closing of the Passenger/Crew Door 52-22-00-860-004 Special Precaution after Maintenance on the Door
Damper and Emergency Operation Cylinder 52-22-00-991-027 Fig. 201 52-22-00-991-001 Fig. 202 52-22-00-991-002 Fig. 203
3. Job Set-up
__________
Subtask 52-22-00-860-062
A. Aircraft Maintenance Configuration
(1)
Make sure that the aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002).
(2)
Make sure that the access platform is in position below the opened door.
1EFF : 301-399, 1 52-22-00Page 213 1 1 May 01/04 1 1 1CES 1
4. Procedure
_________ Subtask 52-22-00-010-056
A. Closing of the Door
(Ref. Fig. 201/TASK 52-22-00-991-027, 203/TASK 52-22-00-991-002)
(1)
Push the release button so that the door stay mechanism releases the door.
(2)
Pull the door rearward until you get access to the door damper and emergency operation cylinder.
(3)
Do the special operation procedure on the door damper and emergency operation cylinder (Ref. TASK 52-22-00-860-004).
(4)
Remove the SAFETY PIN - SLIDE RELEASE LEVER (98D52207551000) from the slide release lever and the frame fitting.
(5)
Move the door rearward and inboard until it is in the correct position at the opening.
(6)
Push down the outboard handle so that the door lowers into the opening.
Subtask 52-22-00-860-063
B. Final Procedure
(Ref. Fig. 201/TASK 52-22-00-991-027, 202/TASK 52-22-00-991-001)
(1)
Open the applicable passenger/crew door (Ref. TASK 52-10-00-010-001).
(2)
Arm the escape slide-release mechanism of the door as follows:
(a)
Remove the PIN - SAFETY SLIDE (98A52107632000) from the slide control handle.
(b)
Push down the slide control handle to the ARMED position.
(c)
Close the protection cover to prevent the direct access to the slide control handle.
(3)
Remove the lock pin from the inflation reservoir as follows:
(a) Remove the lock pin from the operation valve of the inflation reservoir.
1EFF : 301-399, 1 52-22-00Page 214 1 1 May 01/04 1 1 1CES 1
(b)
Put the lock pin in the stowage pocket of the inflation reservoir.
(c)
Make sure that the work area is clean and clear of tool(s) and other items.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(54)
