R Adjustment of the Release Travel
R Figure 518/TASK 52-22-00-991-029
1EFF : 301-399, 1 52-22-00 Page 563
1 1 May 01/04
1 1
1CES 1
R (15) Remove the PIN - SAFETY SLIDE and push down the slide control handle
R (187) in the armed position.
R Subtask 52-22-00-820-062
R C. Adjustment of the Release Travel between the Door Damper and the
R Operation Lever
R (Ref. Fig. 518/TASK 52-22-00-991-029)
R (1) Make sure that the applicable door is closed and in the subesquent
R condition:
R - the release lever (234) of the door damper is fully retracted in
R the safetied position
R - the PIN - SAFETY SLIDE is removed and the slide control handle of
R applicable door is in the armed position
R - the percussion mechanism of the door damper is blocked with the
R related stowage pin (239)
R (2) Measure the distance "U" between the lower edge of the release lever
R (233) and the top of the stop bolt (234) as follows:
R (a) Pull up the inboard handle so that the door lifts but do not open
R it at this stage.
R (b) Loosen the knurrled screw (232) and carefully extend the release
R lever (233) until it contacts the stop bolt (234).
R (c) Put a mark on the stop bolt (234) to indicate the position of the
R lower edge of the release lever (233).
R NOTE : Use a sharp pencil to make a mark on the stop bolt (234).____
R (d) Retract the release lever (233) and safety it with the knurrled
R screw (232).
R (e) Measure the distance between the pencil mark and the top of the
R stop bolt (234):
R NOTE : The dimension must be between 5.5 mm (0.2165 in.) and 6.5____
R mm (0.2559 in.).
1EFF : 301-399, 1 52-22-00Page 564 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 565 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 566 1 1 May 01/04 1 1 1CES 1
R (3) If the distance "U" is out of tolerance, adjust the position of the
R stop bolt (234) as follows:
R (a) If required, bend the tab washer (236) to release the adjustment
R nut (235).
R NOTE : In this case, replace the tab washer (236).____
R (b) Loosen the jam nut (238) and the adjustment nut (235).
R (c) Turn the stop bolt (234) as required until the distance "U" is
R correct.
R (d) Tighten the adjustment nut (235) and the jam nut (238).
R (e) Safety the adjustment nut (235) with the tab washer (236).
R 5. Close-up________
R Subtask 52-22-00-410-063
R A. Close Access
R (1) Remove the BALLAST WEIGHT - EMERGENCY EXIT from the door.
R (2) Install the door linings as removed (Ref. TASK 25-23-47-400-012) and
R (Ref. TASK 25-23-47-400-013).
R (3) Remove the RIGGING PIN - SLIDE RELEASE MECHANISM (98D52207552000)
R (171) from the bellcrank lever (172).
R (4) Install the overhead stowage compartments above the applicable door
R (Ref. TASK 25-24-41-400-001).
R (5) Do the special precaution on the door damper and emergency operation
R cylinder (Ref. TASK 52-22-00-860-004).
R (6) Close the door correctly (Ref. TASK 52-22-00-410-001).
R Subtask 52-22-00-865-063
R B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s):
R -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(78)
