曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  lock fitting (132) as follows: 
R  (a) Loosen the nuts (138) and the bolts (140). 
R  (b) Change the position between the lock fitting (132) and the 
R  serrated plate (131) until the clearance "H" is correct. 
R  (c) Tighten the bolts (140) and the nuts (138). 
R  Subtask 52-22-00-820-057 
R  D. Adjustment of the Outboard Handle 
R  (Ref. Fig. 515/TASK 52-22-00-991-016) 
R  (1) Make sure that the outboard handle (152) is in its fully moved down 
R  position. 
R  (2) Make sure that the contour of the outboard handle (152) is align with 
R  the door skin. 
R  (3) If not, adjust the skin offset of the outboard handle (152) as 
R  follows: 
R  (a) Move the outboard handle (152) fully up. 
R  (b) Loosen the screw (168) and turn the eccentric roller (167) as 
R  required to adjust the skin offset. 
R  (c) If the skin offset is correct, tighten the screw (168). 
R  (4) Measure the clearance "K" between the roller (155) of the outboard 
R  handle (152) and the support fitting (153). 
R  NOTE : The clearance "K" must be between 0.1 mm (0.0039 in.) and 0.2____ 
R  mm (0.0078 in.). 
R  (5) If the clearance "K" is out of tolerance, adjust the position of the 
R  support fitting (153) as follows: 
R  (a) Move the outboard handle (152) fully up.

 

R  Adjustment of the Outboard Handle 
R  Figure 515/TASK 52-22-00-991-016
 1EFF :  301-399,  1  52-22-00 Page 549 
1  1  May 01/04
 1  1
 1CES  1

 

R  (b) Remove the screws (162), the washers (161) and the support 
R  fitting (153) with the shim set (160). 
R  (c) Add or remove the shim sheets (156), (157), (158) or (159) as 
R  required until the clearance "K" is correct. 
R  (d) Put the support fitting (153) and the shim set (160) in position 
R  and attach them with the screws (162) and the washers (161). 
R  (6) Operate the outboard handle (152) fully up so that the door is in the 
R  lifted position. 
R  (7) Move the door inboard and operate the outboard handle down into the 
R  recess of the door skin. 
R  (8) Make sure that the safety handle (151) moves automatically in 
R  position to align with the contour of the outboard handle (152). 
R  (9) If the safety handle (151) does not move in its correct position, 
R  adjust the thickness of the shim set (154) as follows: 
R  (a) Remove the screws (163) and the shim set (154) from the door 
R  structure. 
R  (b) Add or remove the shims (164), (165) and (166) as required. 
R  (c) Install the shim set (154) and the screws (163) on the door 
R  structure. 
R  Subtask 52-22-00-710-052 
R  E. Test Procedure 
R  (1) Do an operational test to make sure that the applicable door operates 
R  satisfactorily (Ref. TASK 52-22-00-710-001). 
R  (2) Make sure that the proximity switches of the applicable door operates 
R  satisfactorily (Ref. TASK 52-71-00-820-007).

 1EFF : 301-399, 1 52-22-00Page 550 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 551 1 1 May 01/04 1 1 1CES 1

R  5. Close-up________ 
R  Subtask 52-22-00-410-058 
R  A. Close Access 
R  (1) Remove the BALLAST WEIGHT - EMERGENCY EXIT from the door. 
R  (2) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (3) Install the door linings (Ref. TASK 25-23-47-400-012) and (Ref. TASK 
R  25-23-47-400-013) on the applicable door. 
R  (4) Do the special precaution on the door damper and emergency operation 
R  cylinder (Ref. TASK 52-22-00-860-004). 
R  (5) Close the door correctly (Ref. TASK 52-22-00-410-001). 
R  Subtask 52-22-00-865-057 
R  B. Make sure that this(these) circuit breaker(s) is(are) closed: 
R  13WN, 15WN, 48WV

 

R TASK 52-22-00-820-004 R Adjustment of the Slide Release Mechanism R 1. Reason for the Job
__________________ R Self Explanatory R 2. Job Set-up Information
______________________
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(74)