(b)
 Remove the nut (9), the washers (7), the bush (3) and the bolt (8).

 (c)
 Disconnect the lower eye-end of the push rod (1) from the fork-end of the shaft lever (5).

 (d)
 If necessary, remove the bush (2) from the shaft lever (5).

 (2)
 Remove the nut (6), the clamp screw (4) and the shaft lever (5) from the inboard handle shaft (32).

 (3)
 Remove the connection rod (28) from the twin lever (31) as follows:

 (a)
 Remove and discard the cotter pin (24) from the nut (25).

 (b)
 Remove the nut (25), the washers (26), the bush (27) and the bolt (30).

 1EFF : 301-399, 1 52-22-21Page 403 1 1 May 01/04 1 1 1CES 1

 Access Plate and Rigging Pins
 Figure 401/TASK 52-22-21-991-008
 1EFF :  301-399,  1  52-22-21 Page 404 
1  1  May 01/04
 1  1
 1CES  1

 Inboard Handle Assembly
 Figure 402/TASK 52-22-21-991-001
 1EFF :  301-399,  1  52-22-21 Page 405 
1  1  May 01/04
 1  1
 1CES  1

 (c)
 Remove the lower eye-end of the connection rod (28) from the fork-end of the twin lever (31).

 (d)
 If necessary, remove the bush (29) from the twin lever (31).

 (4)
 Remove the pull rod (15) from the shaft lever (31) as follows:

 (a)
 Remove and discard the cotter pin (21) from the nut (22).

 (b)
 Remove the nut (22), the washers (18), the bush (16) and the bolt (19).

 (c)
 Remove the lower eye-end of the pull rod (15) from the fork-end of the twin lever (31).

 (d)
 If necessary, remove the bush (20) from the twin lever (31).

 (5)
 Remove the nut (17) and the clamp screw (23) from the twin lever
 (31).

 (6)
 Remove the nut (14) and the clamp screw (11) from the inboard handle (13).

 (7)
 To get access to the inboard handle shaft (32), remove the screws
 (43), the washers (42) and the access plate (41) from the door
 structure.
 (Ref. Fig. 401/TASK 52-22-21-991-008)

 (8)
 Remove the washers (33) and (34) from the inboard handle shaft (32).

 (9)
 Move the inboard handle shaft (32) rearwards until it comes free from the bearing bush (38).

 (10)
 Remove the twin lever (31), the inboard handle (13) and the washer set (12) from the inboard handle shaft (32).

 (11)
 Remove the inboard handle shaft (32) from the door structure.

 (12)
 If necessary, remove the bearing bush (38) from the door structure.

 1EFF : 301-399, 1 52-22-21Page 406 1 1 May 01/04 1 1 1CES 1

 TASK 52-22-21-400-001 Installation of the Inboard Handle Assembly
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  access platform 3.2 m (10 ft. 6 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004  USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
10 cotter pin 52-22-21 09A-400 21 cotter pin 52-22-21 12 -150 24 cotter pin 52-22-21 12 -120
 1EFF : 301-399, 1 52-22-21Page 407 1 1 May 01/04 1 1 1CES 1

 D. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-012  Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
 25-23-47-000-013  Removal of the Door Linings of the RH FWD Emergency Exit Door at zone 251 or RH AFT at zone 252 or LH AFT at zone 232.
 25-23-47-400-012  Installation of the Door Linings of the LH FWD Emergency Exit Door, zone 231
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(111)