-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-004 Removal of the Door Frame Linings of the LH FWD
Emergency Exit Door, zone 231
25-23-47-000-009 Removal of the Door Frame Linings of the RH FWD
Emergency Exit Door, zone 232
25-23-47-000-010 Removal of the Door Frame Linings of the LH/RH AFT
Emergency Exit Doors, zones 251/252.
52-22-00-010-001 Opening of the Emergency Exit Doors from the
Passenger Compartment
52-22-00-410-001 Closing of the Emergency Exit Doors from the
Passenger Compartment
52-22-00-820-002 Adjustment of the Emergency Exit Door
52-22-00-860-003 Special Precaution before Maintenance on the Door
Damper and Emergency Operation Cylinder
52-22-00-860-004 Special Precaution after Maintenance on the Door
Damper and Emergency Operation Cylinder
52-22-12-400-004 Installation of the Guide Arm Assy
52-22-31-991-003 Fig. 406
3. Job Set-up__________
Subtask 52-22-31-860-052
A. Aircraft Maintenance Configuration
(1)
Make sure that the applicable emergency exit door (referred to as door) is opened as required (Ref. TASK 52-22-00-010-001).
(2)
Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).
(3)
Make sure that the access platform is in position below the partly opened door.
(4)
Make sure that the applicable door frame linning is removed as required (Ref. TASK 25-23-47-000-004), (Ref. TASK 25-23-47-000-009) or (Ref. TASK 25-23-47-000-010).
(5)
Make sure that the insulation blakets are removed as required.
1EFF : 301-399, 1 52-22-31Page 434 1 1 May 01/04 1 1 1CES 1
4. Procedure
_________ Subtask 52-22-31-910-052
A. Preparation for Installation
(Ref. Fig. 406/TASK 52-22-31-991-003)
(1) Remove the old sealant from the hinge fittings (54) and (59), the serrated plates (52), (53), (57) and (58) and the door frame
NOTE : Use a wooden or plastic scraper.
____
(2)
Clean the component interface and/or the adjacent area.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Apply a layer of SEALANTS (Material No. 09-016) to the mating surface of the bolts (56) and the nuts (51).
Subtask 52-22-31-420-052
B. Installation of the Guide-Arm Attachment Fittings
(Ref. Fig. 406/TASK 52-22-31-991-003)
(1) Install the guide-arm hinge fitting (54) (referred to as hinge fitting) as follows:
(a) Put the hinge fitting (54) and the serrated plates (52) and (53) in position at the filler plates of the door frame.
NOTE : Make sure that their identification notches align.
____
(b) Install the bolts (56), the washers (55) and the nuts (51).
(2) Install the guide-arm hinge fitting (59) (referred to as hinge fitting) as follows:
(a) Put the hinge fitting (59) and the serrated plates (58) and (57) in position at the filler plates of the door frame.
NOTE : Make sure that their identification notches align.
____
(b) Install the bolts (56), the washers (55) and the nuts (51).
(3) Install the guide arm on the applicable hinge fitting (54) or (59) (Ref. TASK 52-22-12-400-004).
1EFF : 301-399, 1 52-22-31Page 435 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-31-820-052
C. Adjust the parallel motion of the emergency exit door (Ref. TASK 52-22-00-820-002).
5. Close-up
________ Subtask 52-22-31-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Apply a layer of SEALANTS (Material No. 09-013) around the edges of the hinge fittings (54) and (59).
(3)
Apply a layer of STRUCTURE PAINTS (Material No. 16-006) and STRUCTURE PAINTS (Material No. 16-002) to the nuts (56) and the bolts (59).
(4)
Put the removed insulation blankets on the door frame and attach them with the VELCRO tapes.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(153)
