(b)
 Put the upper eye-end of the pull rod (15) in position in the lower fork-end of the twin lever (31).

 (c)
 Install the bolt (19), the washers (18), the bush (16) and the nut (22).

 (d)
 Tighten the nut (22) and safety it with the new cotter pin (21).

 (11)
 Attach the connection rod (28) to the twin lever (31) as follows:

 (a)
 If removed, install the bush (29) in the upper fork-end of the twin lever (31).

 (b)
 Put the lower eye-end of the connection rod (28) in position in the upper fork-end of the twin lever (31).

 (c)
 Install the bolt (30), the washers (26), the bush (27) and the nut (25).

 (d)
 Tighten the nut (25) and safety it with the new cotter pin (24).

 (12)
 Attach the push rod (1) to the shaft lever (5) as follows:

 (a)
 If removed, install the bush (2) in the fork-end of the shaft lever (5).

 (b)
 Put the lower eye-end of the push rod (1) in position in the fork-end of the shaft lever (5).

 (c)
 Install the bolt (8), the washers (7), the bush (3) and the nut (9).

 (d)
 Tighten the nut (9) and safety it with the new cotter pin (10).

 (13)
 Remove the PIN - RIGGING, DOOR MECHANISM from the adjustment lever unit and the locking shaft assembly.

 (14) Install the arm/disarm unit (Ref. TASK 52-22-22-000-001). Subtask 52-22-21-720-050
 C. Do the operational test to make sure that the door handle mechanism operates satisfactorily (Ref. TASK 52-22-00-710-001).
 1EFF : 301-399, 1 52-22-21Page 411 1 1 May 01/04 1 1 1CES 1

 5. Close-up
________ Subtask 52-22-21-865-052
 A. Make sure that this(these) circuit breaker(s) is(are) closed:
 13WN, 15WN, 48WV

 Subtask 52-22-21-410-051
 B. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the insulation mats in the door structure.

 (3)
 Install the door lining (Ref. TASK 25-23-47-400-012) or (Ref. TASK 25-23-47-400-013).

 (4)
 Do the special precaution for the door damper and emergency operation cylinder (Ref. TASK 52-22-00-860-004).

 (5)
 Close applicable the door (Ref. TASK 52-22-00-410-001).

 (6)
 Remove the access platform(s).

 1EFF : 301-399, 1 52-22-21Page 412 1 1 May 01/04 1 1 1CES 1 TASK 52-22-21-000-002

 Removal of the Outboard Handle Assembly
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 3.2 m (10 ft. 6 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-012  Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
 25-23-47-000-013  Removal of the Door Linings of the RH FWD Emergency Exit Door at zone 251 or RH AFT at zone 252 or LH AFT at zone 232.
 52-22-00-010-001 Opening of the Emergency Exit Doors from the Passenger Compartment 52-22-00-860-003 Special Precaution before Maintenance on the Door
 Damper and Emergency Operation Cylinder 52-22-22-000-001 Removal of the Arm/Disarm Unit 52-22-21-991-008 Fig. 401 52-22-21-991-002 Fig. 403
 1EFF : 301-399, 1 52-22-21Page 413 1 1 May 01/04 1 1 1CES 1

 3. Job Set-up
__________ Subtask 52-22-21-010-060
 A. Get Access
 (1)
 Open the applicable emergency exit door (referred to as door) as required (Ref. TASK 52-22-00-010-001).

 (2)
 Make sure that the access platform is in position below the partly opened door.

 (3)
 Make sure that the special precaution on the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).

 Subtask 52-22-21-865-053
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(113)