1EFF : 301-399, 1 52-22-00Page 529 1 1 May 01/04 1 1 1CES 1R Lateral and Lower Gaps Fuselage/Emergency Exit Door R Figure 508/TASK 52-22-00-991-010
1EFF : 301-399, 1 52-22-00Page 530 1 1 May 01/04 1 1 1CES 1
R Adjustment of Lateral Gaps
R Figure 509/TASK 52-22-00-991-011
1EFF : 301-399, 1 52-22-00 Page 531
1 1 May 01/04
1 1
1CES 1
R Adjustment of Lower Gaps
R Figure 510/TASK 52-22-00-991-012
1EFF : 301-399, 1 52-22-00 Page 532
1 1 May 01/04
1 1
1CES 1
R (4) If the lateral gaps "E" or the distance "G" are out of tolerance,
R change the quantity of the adjustment washers (42) as follows:
R NOTE : The adjustment washers (42) are installed between the fork-end____
R of the support arm (43) and the control lever (48).
R (a) Remove and discard the cotter pin (50) from the nut (49).
R (b) Remove the nut (49), the washers (46), the upper hinge bolt (45)
R and the bracket (67) from the control lever (48).
R (c) Remove the bracket (67), the washer (41), the adjustment washers
R (42) and the bushes (47) from the spacer tube (44).
R (d) Change the quantity of the adjustment washers (42) as required
R until the lateral gaps "E" are correct.
R (e) Put the bracket (67), the adjustment washers (42) and the washer
R (41) in position and install the bushes (47) into the journal
R tube (44).
R (f) Install the upper hinge bolt (45), the washers (46) and the nut
R (49) on the control lever (48).
R (g) Measure the clearance "H" between the adjustment washers (42) and
R the spacer tube (44).
R NOTE : A clearance of 0.05 mm (0.0019 in.) is permitted.____
R (5) If the lower gap "F" is out of tolerance, change the quantity of the
R adjustment washers (63) as follows:
R (a) Remove the nut (49), the washers (46) and the upper hinge pin
R (45) from the control lever (48).
R (b) Remove the journal pin (61) from the upper fork-end of the
R support arm (43).
R (c) Change the quantity of the adjustment washers (63) as required
R until the lower gaps "F" are correct.
R (d) Install the journal pin (61) in the upper fork-end (43).
R (e) Measure the clearance "J" between the adjustment washers (63) and
R the spacer tube (44).
R NOTE : A clearance of 0.05 mm (0.0019 in.) is permitted.____
1EFF : 301-399, 1 52-22-00Page 533 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 534 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 52-22-00Page 535 1 1 May 01/04 1 1 1CES 1 TASK 52-22-00-820-003
R (f) Install the upper hinge pin (45), the washers (46) and the nut
R (49) to the control lever (48).
R (g) Tighten the nut (49) and safety it with the new cotter pin (50).
R (6) To set the door in the vertical position, change the quantity of the
R adjustment washers (52) as follows:
R (a) Remove and discard the cotter pin (60) from the nut (59).
R (b) Remove the nut (59), the washers (56) and the lower hinge bolt
R (55) from the lifting lever (58).
R (c) Remove the bracket (68), the washer (51), the adjustment washers
R (52) and the bushes (57) from the spacer tube (54).
R (d) Change the quantity of the adjustment washers (52) as required
R until the lateral gaps "E" are correct.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(69)
