(b)
 Remove the holllow shaft lever (75), the spacer (86) and the washer (85) from the hollow shaft (84).

 (9)
 If necessary, remove the flange bearing (88) as follows:

 (a)
 Remove the nuts (89) and the bolts (87) from the flange bearing (88).

 (b)
 Remove the flange bearing (88) from the door structure.

 (10) Remove and discard the lock washers (55) and (71) from the clamp screws (54) and (72).
 1EFF : 301-399, 1 52-22-21Page 418 1 1 May 01/04 1 1 1CES 1 TASK 52-22-21-400-002

 Installation of the Outboard Handle Assembly
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.2 m (10 ft. 6 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
 SYNTH.ESTER BASED GREASE HIGH PRESSURE
 (Ref. 20-31-00) Material No. 16-002 GB BAEP 3536
 POLYURETHANE TOPCOAT GREY (FOR INTERNAL APPLIC.)
 (Ref. 20-31-00) Material No. 16-006
 ANTI-CORROSION PRIMER (EPOXY-IMPRVD ADHESION)
 (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
44 cotter pin 52-22-21 13A-350 55 lock washer 52-22-21 13A-250 62 cotter pin 52-22-21 12 -090 65 packing 52-22-21 13A-370 71 lock washer 52-22-21 13A-250 73 cotter pin 52-22-21 11 -270 90 key washer 52-22-21 13A-100
 1EFF : 301-399, 1 52-22-21Page 419 1 1 May 01/04 1 1 1CES 1 D. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-23-47-000-012 25-23-47-000-013
25-23-47-400-012 25-23-47-400-013
52-22-00-010-001 52-22-00-410-001 52-22-00-710-001
52-22-00-860-003
52-22-00-860-004
52-22-22-000-001 52-22-22-400-001 52-22-21-991-008 52-22-21-991-002
3. Job Set-up
__________ Subtask 52-22-21-865-054
Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231Removal of the Door Linings of the RH FWD Emergency Exit Door at zone 251 or RH AFT at zone 252 or LH AFT at zone 232.Installation of the Door Linings of the LH FWD Emergency Exit Door, zone 231Installation of the Door Linings of the RH FWD Emergency Exit Door at zone 251, or RH AFT at zone 252, or LH AFT at zone 232.Opening of the Emergency Exit Doors from the Passenger CompartmentClosing of the Emergency Exit Doors from the Passenger CompartmentOperational Check of Door Locking /Unlocking and Opening/Closing from Inside and Outside with Door Latching/Unlatching and Functional Check of Hand ForceSpecial Precaution before Maintenance on the Door Damper and Emergency Operation CylinderSpecial Precaution after Maintenance on the Door Damper and Emergency Operation CylinderRemoval of the Arm/Disarm UnitInstallation of the Arm/Disarm UnitFig. 401Fig. 403
 A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
 1EFF : 301-399, 1 52-22-21Page 420 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-21-860-051

 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the emergency exit door (referred to as door) is opened as required (Ref. TASK 52-22-00-010-001).

 (2)
 Make sure that the access platform is in position below the partly opened door.

 (3)
 Make sure that the special precaution of the door damper and emergency operation cylinder is completed (Ref. TASK 52-22-00-860-003).

 (4)
 Make sure that the door lining is removed (Ref. TASK 25-23-47-000-012) or (Ref. TASK 25-23-47-000-013).

 (5)
 Make sure that the arm/disarm unit is removed (Ref. TASK 52-22-22-000-001).

 4. Procedure
_________ Subtask 52-22-21-910-051
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(115)