(a)
Remove and discard the lockwire from the nuts (123).
(b)
Loosen the nuts (123) and release the lockwashers (124).
(c)
Loosen the clamp (126).
(d)
Turn the barrel of the rod (125) to retract it.
(5)
Slowly close the door and make sure that there is no hard contact between the telescopic fork ends (132) and the girt bar fittings (131). (Ref. Fig. 410/TASK 52-13-11-991-012)
R **ON A/C 062-099, 105-149, 151-199, 204-299, 301-399, 401-499,
Subtask 52-13-11-820-052-A
C. Adjustment of the Door in its Frame During the Door Closing Operation (Ref. Fig. 406A/TASK 52-13-11-991-011-A, 407/TASK 52-13-11-991-016)
**ON A/C 062-099, 105-105, 151-154, 204-207,
(Ref. Fig. 409/TASK 52-13-11-991-019) R **ON A/C 106-149, 155-199, 208-299, 301-399, 401-499,
(Ref. Fig. 409A/TASK 52-13-11-991-019-A) R **ON A/C 062-099, 105-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 410/TASK 52-13-11-991-012)
1EFF : ALL 1 52-13-11Page 437 1 1 Aug 01/05 1 1 1CES 1
(1)
Slowly close the door and make sure that there is no hard contact between the door stops (101) and the frame stops (112). (Ref. Fig. 411/TASK 52-13-11-991-008)
(2)
The clearance H2 must be 0.2 mm minimum for an overlap H3 of 3 mm (0.1181 in.) to 4 mm (0.1574 in.). The guide rollers (81) touch the guide fittings (82) and (86).
(3)
If the clearance H2 is not in the tolerances, adjust the upper and lower guide fittings (82) and (86) as follows:
(a)
Open the door and identify the position of the serration plates
(89) and (90), and the upper and lower guide fittings (82), (86).
(b)
Loosen the screws (80) and move the guide fittings (82), (86) to get the clearance H2.
(c)
Make sure that the eccentric washers (88):
-fully seal the holes of the guide fittings (82) and (86),
-
are not above the rounded areas or spot-facing edges,
-
are not out of the outer contour of the fitting.
(d)
Temporarily tighten the screws (80).
(4) Release the upper hook as follows:
**ON A/C 062-099, 105-105, 151-154, 204-207,
(Ref. Fig. 409/TASK 52-13-11-991-019) R **ON A/C 106-149, 155-199, 208-299, 301-399, 401-499,
(Ref. Fig. 409A/TASK 52-13-11-991-019-A) R **ON A/C 062-099, 105-149, 151-199, 204-299, 301-399, 401-499,
(a)
Remove and discard the lockwire from the nuts (123).
(b)
Loosen the nuts (123) and release the lockwashers (124).
(c)
Loosen the clamp (126).
(d)
Turn the barrel of the rod (125) to retract it.
R 1EFF : 062-099, 105-149, 151-199, 204-299, 1 52-13-11Page 438 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(5) Slowly close the door and make sure that there is no hard contact between the telescopic fork ends (132) and the girt bar fittings (131). (Ref. Fig. 410/TASK 52-13-11-991-012)
**ON A/C ALL
Subtask 52-13-11-820-053
D. Adjustment of the Door in the Down Position (Ref. Fig. 403/TASK 52-13-11-991-005, 408/TASK 52-13-11-991-006, 411/TASK 52-13-11-991-008)
(1)
Install two positioning templates on the X axis, on the door frame: (Ref. Fig. 411/TASK 52-13-11-991-008)
(a)
Install one template between the longerons L5 and L6.
(b)
Install the other template between the longerons L2 and L3.
(2)
If the templates do not touch the door frame or the door contour in the X axis: (Ref. Fig. 403/TASK 52-13-11-991-005)
(a)
Disconnect the upper and lower connection links (59) from each side of the yoke (54).
(b)
Remove the nuts (57), the washers (58), (61) and the bolts (60) to disconnect the upper and lower connection links (59).
(c)
Adjust the door in the X axis with the washers (64) of a different thickness.
(d)
Make sure that the clearance B is less than or equal to 0.1 mm (0.0039 in.).
NOTE : The thickness of the two washers (62) at level of the
____ lower and upper connection links (59) is equal to the nominal thickness. Clearance B must be in the tolerance.
(e)
Connect the upper and lower connection links (59).
(f)
Install the washers (61), the bolts (60).
(g)
Install the washers (58) and the nuts (57).
1EFF : ALL 1 52-13-11Page 439 1 1 May 01/04R 1 1 1CES 1
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(82)
