(18)
 Connect the rod (317).

 (a)
 Install the bushes (318) and (319) with SPECIAL MATERIALS (Material No. 05-002), the washer (316) and the bolt (315).

 (b)
 Install the bushes (320) and the nut (322).

 1EFF : ALL 1 52-13-21Page 473 1 1 Feb 01/01R 1 1 1CES 1

 Reducer Shaft Mechanism - Adjustment Figure 416/TASK 52-13-21-991-017
 1EFF : 1 1R 1CES  ALL  1 11 1 52-13-21 Page 474 Feb 01/01

 (c)
 TORQUE the nut (322) to between 0.6 and 0.7 m.daN (53.09 and

 61.94 lbf.in).

 (d)
 Install a new cotter pin (321). NOTE : If you install a new bolt (315), drill a hole of 1.9 mm

____ (0.0748 in.) for the cotter pin installation.
 (19)
 Remove the PIN - RIGGING (98D52103006000) from the fitting (306) and the bellcrank (333).

 (20)
 Open the door (door up position).

 (21)
 Install the PIN - RIGGING (98D52103006000) in the fitting (306) and the bellcrank (333).

 (22)
 Make sure that there is contact between the stop (348) fitted on the bellcrank (333) and the door structure.

 (23)
 If there is no contact, adjust as follows:

 (a)
 Remove the nut (347).

 (b)
 Remove and discard the lockwasher (343). Remove the washer (342).

 (c)
 Adjust the setscrew (346) to get the contact.

 (d)
 Apply LUBRICANTS (Material No. 06-005) on the threads of the setscrew (346).

 (e)
 Install the washer (342) and a new lockwasher (343).

 (f)
 Install the nut (348) and tighten it.

 (g)
 Safety the nut (347) with the lockwasher (340).

 (24)
 Do a check of the rigging of the bellcrank (348) located on the compensation mechanism with the RIGGING PIN (98DNSA20206120). The door is in the up position.

 (25)
 Remove the PIN - RIGGING (98D52103006000) from the fitting (306) and the bellcrank (333).

 1EFF : ALL 1 52-13-21Page 475 1 1 Feb 01/01R 1 1 1CES 1

 Subtask 52-13-21-420-058
 H. Installation of the Compensation Mechanism
 (Ref. Fig. 410/TASK 52-13-21-991-018, 417/TASK 52-13-21-991-019)

 (1)
 Make sure that the door is open.

 (2)
 Install the spacer (538), the crank (539) and the spacer (541) on the sleeve (537).

 NOTE : When you install the crank (539) on the sleeve (537), make
____
 sure that the grooves are aligned.

 (3)
 Put the sleeve (537) in position and push it to the outer side of the door.

 (4)
 Apply SEALANTS (Material No. 09-018) on the surface of the bearing assy (542) in contact with the door structure.

 (5)
 Install the bearing assy (542), the bolts (503) and the nuts (513) and tighten them.

 (6)
 Install the sleeve (537) on the bearing assy (542) and put the spacer

 (543) between the sleeve (537) and the bearing assy (542).

 (7)
 Apply SEALANTS (Material No. 09-018) on the surface of the bearing assy (535) in contact with the door structure.

 (8)
 Install the bearing assy (535), the bolts (502) and the nuts (501) and tighten them.

 (9)
 Install the washer (544).

 (10)
 Install the STA-LOK nut (545) (Ref. TASK 20-22-00-400-001).

 (11)
 TORQUE the STA-LOK nut (545) to between 0.3 and 0.4 m.daN (26.54 and

 35.39 lbf.in).

 (12)
 Apply SEALANTS (Material No. 09-018) on the surface of the bearing assy (523) in contact with the door structure.

 (13)
 Install the bearing assy (523), the bolts (524) and the nuts (522) and tighten them.

 (14)
 Install the washer (519) and the spacer (520) on the torsion tube (518).

 1EFF : ALL 1 52-13-21Page 476 1 1 Feb 01/01R 1 1 1CES 1

 INTENTIONALLY BLANK

R 1 1
52-13-21Page 477
1 1 Feb 01/01 1 1 1CES 1

 Compensation Mechanism - Adjustment Figure 417/TASK 52-13-21-991-019- 12 (SHEET 1)
 1EFF : 1 1R 1CES  ALL  1 11 1 52-13-21 Page 478 Feb 01/01

 Compensation Mechanism - Adjustment Figure 417/TASK 52-13-21-991-019- 22 (SHEET 2)
 1EFF : 1 1R 1CES  ALL  1 11 1 52-13-21 Page 479 Feb 01/01

 (15)
 Install the torsion tube (518) in the bearing (523).

 (16)
 Apply SEALANTS (Material No. 09-018) on the surface of the bearing assy (517) in contact with the door structure.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(129)