(4)
Remove the nuts (2) of the retainer (11), then the retainer (11) and the screws (21).
(5)
Remove the nuts (2) of the retainer (12), then the retainer (12) and the screws (21).
(6)
Remove the nuts (2) of the retainer (13), then the retainer (13) and the screws (21).
(7)
Remove the nuts (2) of the retainer (7), then the retainer (7) and the screws (21).
(8)
Remove the nuts (2) of the retainer (6), then the retainer (6) and the screws (21).
(9)
Remove the nuts (2) of the retainer (5), then the retainer (5) and the screws (21).
1EFF : ALL 1 52-13-18Page 402 1 1 Feb 01/98 1 1 1CES 1
Seal of the Aft Passenger/Crew Door
Figure 401/TASK 52-13-18-991-001
1EFF : ALL 1 52-13-18 Page 403
1 1 Feb 01/98
1 1
1CES 1
(10)
Remove the nuts (2) of the retainer (4), then the retainer (4) and the screws (21).
(11)
Remove the nuts (2) of the retainer (14), then the retainer (14) and the screws.
(12)
Remove the nuts (2) of the retainer (15), then the retainer (15) and the screws (21).
(13)
Remove the nuts (2) of the retainer (16), then the retainer (16) and the screws (21).
(14)
Remove the nuts (2) of the retainer (3), then the retainer (3) and the screws (21).
(15)
Remove the nuts (2) of the retainer (1), then the retainer (1) and the screws (21), (22).
(16)
Remove the nuts (2) of the retainer (19), then the retainer (19) and the screws (22).
(17)
Remove the nuts (2) of the retainer (18), then the retainer (18) and the screws (22).
(18)
Remove the nuts (2) of the retainer (17), then the retainer (17) and the screws (21), (22).
(19)
Remove the seal (20) of the passenger/crew door.
1EFF : ALL 1 52-13-18Page 404 1 1 Feb 01/98 1 1 1CES 1
TASK 52-13-18-400-001
Installation of the Door Seal
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
-
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
1EFF : ALL 1 52-13-18Page 405 1 1 May 01/05 1 1 1CES 1 C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew Door 52-13-18-991-001 Fig. 401 R 52-13-18-991-006 Fig. 402
3. Job Set-up
__________
Subtask 52-13-18-010-056
A. Aircraft Maintenance Configuration
(1)
Make sure that the platform is in position.
(2)
Make sure that the applicable passenger/crew door 832, 842 are open.
(3)
Make sure that the special precautions are obeyed (Ref. TASK 52-10-00-860-001).
Subtask 52-13-18-110-050
B. Cleaning.
(1) Clean the seal and the working surface and apply the CLEANING AGENTS (Material No. 11-004).
4. Procedure
_________
Subtask 52-13-18-420-052
A. Installation of the Door Seal.
(Ref. Fig. 401/TASK 52-13-18-991-001)
(1)
Put the seal (20) on the passenger/crew door.
(2)
Install the retainer (17), the screws (21), (22), and the nuts (2) and tighten them with your hand.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(107)
