____ (0.0748 in.) for the cotter pin installation.
 (17)
 Install PIN - RIGGING (98D52103006000) on the bellcrank assembly (125).

 (18)
 Connect the rod (92) as follows: (Ref. Fig. 407/TASK 52-13-21-991-014, 409/TASK 52-13-21-991-016)

 (a)
 Remove and discard the lockwire from the nuts (142).

 (b)
 Loosen the nuts (142) and release the lockwashers (143).

 (c)
 Turn the barrel of the rod (92) to get the connection.

 (d)
 Install the bushes (93), (98) and the bolt (94).

 (e)
 Install the washer (95) and the nut (96) and tighten it.

 (f)
 Install a new cotter pin (97). NOTE : If you install a new bolt (94), drill a hole of 2 mm

____ (0.0787 in.) for the cotter pin installation.

 (g)
 Tighten the nuts (142).

 (h)
 Make sure that the lockwashers (143) are correctly positioned.

 1EFF : ALL 1 52-13-21Page 467 1 1 Aug 01/04R 1 1 1CES 1

 (i) Safety the nuts (142) and the lockwashers (143) with MISCELLANEOUS (Material No. 19-010).
 (19) Adjustment of the upper stops.
 (a)
 Make sure that the PIN - RIGGING (98D52103006000) is in position in the bellcrank assembly (125).

 (b)
 Make sure that there is contact between the kinematic stop (132) of the bellcrank assy (125) and the door structure.

 (c)
 If there is no contact, adjust as follows:

 (d)
 Put the lever assembly (122) in contact with the bellcrank assy (123). Make sure that the clearance J6 is 0.5 +0 +0.1 mm (0.0196 +0.0000 +0.0039 in.).

 (e)
 If the clearance J6 is not in the tolerances, adjust as follows: 1 Loosen the nut (133).

 1_ Loosen the nut (133).
 2_ Remove and discard the lockwasher (134). Remove the washer
 (135).
 3_ Adjust the setscrew (136) to get the contact.
 4_ Apply LUBRICANTS (Material No. 06-005) on the threads of the
 setscrew (136).
 5_ Install the washer (135), the new lockwasher (134) and the nut
 (133).
 6_ TORQUE the nut (133) to between 0.3 and 0.4 m.daN (26.54 and
 35.39 lbf.in).
 7_ Safety the nut (133) with the lockwasher (134).

_ 2 Remove and discard the lockwasher (134). Remove the washer
_ (135).
 3 Adjust the setscrew (136) to get the clearance.
_ 4 Apply LUBRICANTS (Material No. 06-005) on the threads of the
_ setscrew (136)
 1EFF : ALL 1 52-13-21Page 468 1 1 Aug 01/04R 1 1 1CES 1

 5_ Install the washer (135), the new lockwasher (134) and the nut
 (133).
 6_ TORQUE the nut (133) to between 0.3 and 0.4 m.daN (26.54 and
 35.39 lbf.in).
 7_ Safety the nut (133) with the lockwasher (134).

 (20)
 Remove the PIN - RIGGING (98D52103006000).

 (21)
 Connect the rod (75).

 (a)
 Put the rod (75) in position in its fitting.

 (b)
 Install the bushes (71) and (72) with SPECIAL MATERIALS (Material No. 05-002), the washer (73) and the bolt (74).

 (c)
 Install the washer (70) and the nut (69).

 (d)
 TORQUE the nut (69) to between 0.6 and 0.7 m.daN (53.09 and 61.94 lbf.in).

 (e)
 Install a new cotter pin (68). NOTE : If you install a new bolt (74), drill a hole of 1.9 mm

____ (0.0748 in.) for the cotter pin installation.
 (22) Check and adjustment of the locking hook (138) (Ref. TASK 52-13-21-820-001).
 (a)
 Open the door and put two shims in the upper guide fittings.

 (b)
 Close the door.

 (c)
 Adjust the locking hook (138) as follows: 1 Turn the barrel of the rod (75) until the locking hook (138)

_ is in contact with the roller (137).
 2 Tighten the nuts (139) and the clamp (147).
_
 3 Make sure that the lockwashers (140) are correctly positioned.

_
 4 Safety the nuts (139) and the lockwashers (140) with

_ MISCELLANEOUS (Material No. 19-010).
 (d) Open the door and remove the shims.
 1EFF : ALL 1 52-13-21Page 469 1 1 Aug 01/04R 1 1 1CES 1

 (23)
 Installation of the plate (113). (Ref. Fig. 407/TASK 52-13-21-991-014)

 (a)
 Install the set of washers (112) and put the plate (113) in position.

 (b)
 Make sure that the clearance J8 is 0.3 +0 +0.5 mm (0.0118 +0.0000 +0.0196 in.).

 (c)
 If the clearance J8 is not in the tolerances, adjust the set of washers (112).
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(127)